Are you experiencing issues with your Electrolux appliance, puzzled by perplexing error codes? Welcome to our blog, where we delve into the world of Electrolux appliances error codes, providing insightful solutions.
Electrolux Washer Error Codes
| Error Code | Description |
|---|---|
| E10 | Water inlet fault Learn More |
| E11 | Your washer isn’t filling with water during the washing phase of the cycle Learn More |
| E12 | This error code means your washer isn’t filling with water during the rinsing phase of the cycle Learn More |
| E13 | Water level is dropping when it shouldn’t, so there is likely a leak Learn More |
| E20 | Your washing machine has a drain fault Learn More |
| E21 | This error code is another drain fault code Learn More |
| E22 | Your washer isn’t draining after the rinse cycle Learn More |
| E23 | Your Electrolux washing machine has detected an issue between the drain pump triac sensing and the triac status Learn More |
| E24 | This error code indicates a fault in the sensing circuit of the drain pump triac Learn More |
| E25 | Wrong input signal is being sent to the microprocessor in your washer Learn More |
| E31 | This code means the pressure switch is faulty Learn More |
| E32 | Pressure switch has a calibration problem Learn More |
| E35 | Pressure sensor in your washer has detected the water level is too high Learn More |
| E40, E41, E42, E43, E44, and E45 | These error codes indicate a problem with the door lock Learn More |
| E50 | Problem with the motor in your washing machine Learn More |
| E60 | This error code indicates a heating fault Learn More |
| E61 | It indicates a problem with the water not heating during the wash cycle Learn More |
| E62 | Water is overheating during the wash cycle Learn More |
| EC1 | PCB is receiving a signal from the flow meter telling it that water is flowing into the washing machine incorrectly Learn More |
| EF1 | This error code indicates the drain pump filter or one of the hoses is blocked Learn More |
| EF2 | There is too much foam in the washer drum during the spin cycle Learn More |
| EF4 | This error code indicates the flow meter is not detecting any water flowing into your washer even though the water inlet valves are open Learn More |
| EF5 | Washing machine is out of balance Learn More |
Electrolux Dryer Error Codes
| Error Code | Description |
|---|---|
| E31 | Moisture sensor frequency too high Learn More |
| E32 | Moisture sensor frequency too low Learn More |
| E42 | Door sensing error Learn More |
| E51 | Motor relay failure Learn More |
| E52 | Motor stopped or not starting Learn More |
| E53 | Motor centrifugal switch failure Learn More |
| E54 | Motor sensing failure Learn More |
| E61 | Heater relay failure Learn More |
| E63 | Heating element shorted to ground Learn More |
| E64 | Open heating element circuit Learn More |
| E65 | High limit thermostat tripped open too many times (Electric dryer) Learn More |
| E66 | Thermal limiter tripped Learn More |
| E67 | Heating sensor failure Learn More |
| E71 or E72 | Outlet thermistor failure Learn More |
| E73 | Inlet thermistor failure Learn More |
| E74 | Drive motor relay failure Learn More |
| E91 | Communication, error Learn More |
| E92 | User interface control and electronic control board mismatch Learn More |
| E93 | Machine configuration error Learn More |
| E94 | Cycle configuration error Learn More |
| E97 | Program mismatch Learn More |
| EA1 | Incoming power frequency out of limits Learn More |
| EA2 | Incoming line voltage is above 130 volts AC Learn More |
| EA3 | Incoming line voltage is below 90 volts AC Learn More |
| EA4 | Improper wiring on the terminal block Learn More |
| EA5 | Electronic control board defective Learn More |
| EF1 | Blocked exhaust vent Learn More |
| EF3 | Maximum dry time has expired Learn More |
| EF8 | Stuck key on the user interface control Learn More |
Electrolux Dishwasher Error Codes
| Error Code | Description |
|---|---|
| Er-01 | Water leak detected Learn More |
| Er-02 | Thermistor/turbidity sensor failure Learn More |
| Er-03 | Wash motor failure Learn More |
| Er-04 or Er-05 | Upper fan/vent failure Learn More |
| Er-06 | Lower fan failure Learn More |
| Er-07 or Er-11 | Drain valve failure Learn More |
| Er-08 | User interface control failure Learn More |
| Er-09 | Communication failure between the user interface control and the electronic control board Learn More |
| Er-10 | Electronic control board relay failure Learn More |
| Er-12 | Drain valve position error Learn More |
| Er-13 | Electronic control board failure Learn More |
Electrolux Refrigerator Error Codes
| Error Code | Description |
|---|---|
| E1 | Evaporator sensor damaged Learn More |
| E2 | Room temperature sensor damaged (installed on the display board) Learn More |
| E4 | Room temperature sensor damaged (installed on the power board) Learn More |
| E5 | 0 degree compartment sensor damaged Learn More |
| Er | Check J4-4, J4-5 and J4-6 Connector on Icemaker board Learn More |
| t3 | TH3 Sensor (open or short) Go to flow chart for Ice t3 Learn More |
| CE | IM Com Lost Go to flow chart 50C. Put into service mode to verify Learn More |
| OP – Normal | Freezer Sensor OPEN Learn More |
| SH – Normal | Freezer Sensor SHORTED Learn More |
| Normal – OP | Fresh Food Sensor OPEN Learn More |
| Normal – SH | Fresh Food Sensor Shorted Learn More |
| SY – EF | Evaporator Fan Failure Learn More |
| SY – CE | Communication Error Learn More |
| SY – CF | Communication Failure Learn More |
| Ec | Master PCB receive communication failure Learn More |
| Ed | If defrost fault , it will show “Ed”, otherwise display “–” Learn More |
| EF | If fan motor trouble, it will show “EF”, otherwise display “–” Learn More |
Electrolux Oven Error Codes
| Error Code | Description |
|---|---|
| F10 | Control has sensed a potential runaway oven condition Learn More |
| F11 | The key has been pressed for an extended period Learn More |
| F13 | Control’s internal checksum may have become corrupted Learn More |
| F14 | Misconnected keyboard cable Learn More |
| F15 | Controller self check failed Learn More |
| F23 | The controller failed to communicate with the oven lights control board Learn More |
| F30 | Open RTD sensor probe/ wiring problem Learn More |
| F31 | Shorted RTD sensor probe / wiring problem Learn More |
| F43 | The cooling fan speed too slow Learn More |
| F44 | The cooling fan speed too fast Learn More |
| F90 | Door motor mechanism failure Learn More |
| C3 | The cleaning function does not operate Learn More |
| F102 | You did not fully close the door Learn More |
| Demo | The demo mode is activated Learn More |
| F | Oven control has detected a fault or error condition Learn More |