Inside the appliance
Refrigerator and freezer door gasket. In plain English.
The door gasket is the seal around the doors. Electrolux puts a bent gasket or door at the top of its frost causes, and a leaky seal among the reasons for the H or HI high temperature alarm. Both articles send you to check the seal before anything else.

Where it fits.
Refrigerator and freezer door gasket in the appliance
It runs around the edge of each refrigerator and freezer door. The articles give no other position.
The image shows the type of component only. It does not select a replacement that fits your model.
What is different once this system needs attention.
Refrigerator and freezer door gasket concerns may show up with a drop in performance or a code that keeps returning. Testing comes first before anyone decides the component has failed.

Electrolux refrigerator ice maker not working
Little or no ice often comes down to a jam, ice frozen around the auger, a locked display or a water supply problem. Electrolux has a short auger procedure, a DI SP ice-jam article and a no-water checklist that also covers the ice maker.

Electrolux refrigerator or freezer frost buildup
Frost forms when warm and cold air meet below freezing. Electrolux traces it to a gasket or door that cannot seal, a chute flap left ajar, a freezer set colder than 0 degrees F or food blocking the vents.
Owner care, within the model instructions.
Power the appliance down and pull the plug before any owner check. Beware of standing water and sharp debris. Never touch a wet plug or electrical area, take off service panels, or step beyond your model’s owner guide.
- 1
Close the door fully
The frost article asks you to make sure the door shuts completely and nothing blocks it.
- 2
Check the seal
It then says to make sure the gasket seals well. The H or HI article asks for the same check around the doors.
- 3
Look for a warp
KB 1918348 says a bent gasket or door keeps the seal from closing completely. Describe any wave or gap when you book.
- 4
Check the settings
For a kitchen install, Electrolux suggests a 37°F refrigerator and a 0°F freezer. Other settings can bring on the same alarm.
Cleaning or replacement?
Leave internal testing to a technician.
Book a technician if frost or the H alarm returns after the door closes fully and the settings are right.
Book a technician if the gasket looks warped, torn or pulled out of its groove.
Arrange a diagnosticSources and model boundaries.
These sources back the Refrigerator and freezer door gasket guidance. Use the manual for your own model.
- Refrigerators / Freezer - Frost Build Up (KB 1918348)
- Refrigerator Error Code H or HI - High Temperature (KB 1917064)
- What do the alarms or error messages mean on my French-Door refrigerator? (KB 1853035)
Follow the guide for your exact model. Consult how we research these pages.
Does a worn seal let frost form?
Yes. Electrolux counts a bent gasket or door as a cause, because warm air gets in and meets the cold air.
Can it trigger the H or HI alarm?
It can. The article lists an open door, changed settings and a poor seal as causes. The alarm sounds once the freezer reaches 26°F or the refrigerator reaches 55°F.
Which settings does Electrolux suggest?
A 37°F refrigerator and a 0°F freezer in a kitchen, per the H or HI article.
How do I clear the alarm?
Press Clear Alerts, or unplug the unit for 30 seconds and then restore power. Fix the cause first, or the alarm comes back.
Codes, symptoms, parts and service
Link the message to what to do next.
Electrolux refrigerator ice maker not working
Little or no ice often comes down to a jam, ice frozen around the auger, a locked display or a water supply problem. Electrolux has a short auger procedure, a DI SP ice-jam article and a no-water checklist that also covers the ice maker.
Refrigerator repair
Book a diagnostic for your model at the appliance.
Find your metro
Office details and the access information to pass on.

