The care journal

Electrolux appliance care guides for routine care.

Care routines, fixes and code explanations drawn from Electrolux’s own manuals and matched to the models they cover.

Experienced techniciansWarranty on our workmanshipOEM parts available on orderUpfront pricing, agreed before work

Inside this collection.

Error codes explained ·

A code on the dryer? Recall it, then read its group.

To see the last code on an Electrolux dryer, wake it with any button except cancel, then hold cancel and start/pause for 6 seconds. Codes sort by their first digit into contact sensor, motor, heat, thermistor, board, supply and airflow groups, and most groups need a technician.

Error codes explained ·

E61, E64, E65 or E66? Each one tests something different.

On an Electrolux dryer, E61 is the heater relay, E63 a heater short to ground, E64 an open heater circuit, E65 a high-limit thermostat that tripped too often and E66 an open thermal limiter. Only E65 sends the technician to the vent, and every one of them needs a visit.

Error codes explained ·

E91, E92, E93? Three different board problems.

On an Electrolux dryer, E91 means the control board and interface board are not communicating, E92 means they are not compatible and E93 means the machine configuration data failed its check. None is an owner repair, and the model number matters because the sheet's remedies depend on matching parts.

Error codes explained ·

F14 or F15 on the oven? Check which control you have.

F14 appears only on the ES630 oven control and means a misconnected keyboard cable. F15 means a failed controller self check on the ES630 but a keyboard error on the 2017 modular control, so your model number decides which row applies. Switch the oven off for 30 seconds, then book a technician if it comes back.

Error codes explained ·

Washer stopped, nothing on the display? Recall the code.

An Electrolux front-load washer shows only some codes. To read the last stored one, power on, wait at least 10 seconds, then hold temp and select for 3 seconds. The display shows the last error in memory. Hidden codes include E13, E23, E31 and E62, and they need a technician.

Troubleshooting ·

Oven keys or display acting up? Start with lock, demo and a reset.

The Owner Center explains Electrolux oven clock and display settings in video articles with no written steps, so use your Use & Care guide for those. In writing, it covers locked controls, demo mode and a 30-second power reset, and the oven sheets cover keypad codes F11, F13, F14 and F15.

Troubleshooting ·

Oven fan running on? Know which fan it is.

An Electrolux oven has convection fans that circulate air in the cooking functions and a separate cooling fan that runs at low speed during any cooking and stays on until the oven cools. F43 or F45 means that cooling fan runs too slowly, and F44 or F46 means too fast. Check for blocked airflow, then book a visit.

Troubleshooting ·

Dryer making a noise? Start with what is normal.

The Owner Center names one normal dryer sound: a chime when a cycle ends and during Wrinkle Release. Rattling is usually something loose in the drum, a pedestal that has loosened causes clanking or squeaking, and vibrating or walking points to shipping bolts or an unlevel dryer. A motor code is different.

Troubleshooting ·

Detergent left in the drawer? Check the product, the packs and the water.

Electrolux's written sources name no single cause for a drawer that stays full. They list what interferes: a pack in the drawer, detergent above the max fill line, an unseated drawer, buildup, and water that never arrives. Work through these, then book a technician.

Troubleshooting ·

Frost in the freezer? Four things to check.

Electrolux describes frost as condensation that freezes where warm air meets air below 32 °F. Check four things: the door and gasket seal, the chute flap, a freezer setting that has drifted below zero, and food sitting across the vents. Book if frost returns.

Maintenance ·

EF1 on the display? Start at the vent, not the drum.

EF1 and EF3 are airflow codes, and E65 is a high-limit count that the sheet ties to vent restriction. Clean the lint filter, check the exhaust tube for bends and blocks, and look at the vent exit. If a code returns after a clear run, book a visit.

Maintenance ·

Washer slow to fill? Look at the two hoses first.

Hot and cold faucets must be on, the hoses must not be reversed, and the connections must be snug. A reversed pair triggers HO SE or F9, and a washer that cannot fill can lock out with E11 for up to 6 minutes. Fix the hoses first, then book if it persists.

Maintenance ·

SU dS on the display means less detergent, not more rinsing.

SU dS means the washer detected too many suds. It adds rinses until they clear, about 5 minutes each. Use high efficiency detergent, measure to the max fill line or below, run an empty quick wash afterwards and press Cancel to clear the message.

Troubleshooting ·

A washer that thumps on spin usually has a floor or a bolt behind it.

Most washer noises come from three things: shipping material still in place, a washer that is not level on a solid floor, or an unbalanced load. Check for Styrofoam and bolts, set the feet so no leg floats, and spread the load. Clicks, gurgles and a jet-engine spin are normal.

Maintenance ·

Oven door locked after self-clean? Wait for it to cool, then try UNLOCK.

Remove the racks, set the control to clean, pick a time (three hours or medium soiled is the typical choice) and press Start. The latch holds until the oven cools. If the lock will not release or F90 shows, try UNLOCK, then cut the power for up to half a minute.

Using your appliance ·

Clothes too dry, or not dry at all? Check the cycle first.

Try Auto Dry before Timed Dry when clothes come out over-dried. Air Fluff tumbles without heat, so pick Normal Dry with low or medium heat for a regular load. Keep the moisture bars clean so Auto Dry can sense wetness.

Using your appliance ·

DEMO on the oven display? Breaker off for 45 seconds.

DEMO on an Electrolux oven is a mode you can switch off, not a failure. Turn the oven off at the breaker, wait 45 seconds, switch it on, then find demo mode in the settings menu and turn it off. A washer in Demo Mode also needs a key sequence; unplugging will not clear it.

Using your appliance ·

High Temp on the fridge display? Start with the door and the gasket.

Most Electrolux refrigerator alarms are prompts: PF after a power cut, High Temp when a section passes 26 degrees (freezer) or 55 degrees (fridge), Door Ajar after 5 minutes open, Sb for Sabbath mode and DI SP for an ice jam. OP, SH, SY CE, SY CF and SY EF have no printed meaning.

Troubleshooting ·

Washer will not start? Check for the lock icon before anything else.

Check the display. LOC is the control lock: scroll to the control lock option and press Select. E41 means the door switch reads open; E42 means the door lock is not recognized. For both, remove anything keeping the door open and listen for the click. Then check Start, Delay Start and power.

Using your appliance ·

Oven runs hot or cool? Check preheat, rack and gasket first.

Before you adjust anything, preheat fully (up to 20 minutes, empty, door shut), check rack position and bakeware, and look at power and the door gasket. If results are still off, ES630 ovens can be offset by up to 35 degrees Fahrenheit: hold Bake for 6 seconds, enter the number and press Start.

Before following the steps.

Two hands wiping the rubber door gasket of an open front-load washer with a white cloth.

Recall the last code

Wake the dryer, hold cancel and start/pause together for 6 seconds and write down the E and two digits that appear.

Read the full sequence

A message on the display shifts where you start.

E42Owner checks first

Door

E42 appears in two Electrolux documents with two readings. The Owner Center guide shows E 42 as Door Open; the technician chart says door sensing failure with a defective control board. Close the door and clear the doorway; if E42 stays, book a visit.

E53Technician

Motor

E53 is a motor centripetal switch failure on Electrolux's dryer chart. The switch inside the motor, the control board or the wiring is defective. Unplug the dryer and book a technician; the chart's fixes are wiring checks and parts.

E61Technician

Heating

E61 is a heater relay failure on Electrolux's dryer chart: a heater relay is stuck open or closed, or the wiring is defective. If the dryer runs without heat, or heats when it should not, unplug it and book a technician.

E65Owner checks first

Heating

E65 means the high limit thermostat has tripped too many times, per Electrolux's dryer chart. The chart lists a restricted vent first, then the thermostat or, on electric models, the inlet thermal limiter. Clean the lint screen and vent, then book a technician.

E91Technician

Control board

E91 is a communication error between the dryer's control board and its interface board, per Electrolux's dryer chart. The cause is the wiring, the control board or the interface board. Restart once, then book a technician.

EF1Owner checks first

Airflow

EF1 on an Electrolux dryer means the vent is blocked. The chart calls it vent blocked and the Owner Center guide calls it ventilation blockage, a known installation issue. Clean the lint filter, check the exhaust tube and the vent exit.

What we do. Where we stop.

Diagnostics and repair

Experienced technicians inspect the appliance before proposing any work. OEM parts can be ordered, with the right part matched to your model.

Manufacturer-covered repairs

An Electrolux still under its manufacturer warranty goes to Electrolux for covered repairs. Our repairs carry a warranty on our workmanship.

Here to help

Good questions.
Clear answers.

Talk to our team
What topics do the guides handle?

Care, daily use, troubleshooting and plain explanations of codes. Each rests on Owner Center articles or technician sheets, which are listed at the foot of the page.

How do I choose where to begin?

With a code on the screen, begin in the codes guide. With odd behavior and no message, open troubleshooting. To prevent trouble, read the care guide.

Is reading a guide the same as a repair?

No. They stop at owner-level tasks like filters, hoses and leveling. Opening panels, touching wiring, working on gas lines or sealed systems is a technician's job.

Will the guide fit my particular model?

Possibly not. Electrolux changed controls over the years, so every page states which machines it describes. Compare that line with the plate on your unit.

Let’s take care of it.

Premium appliances deserve
careful service.