On this page
- Recall: power on, wait at least 10 seconds, hold temp and select (set) for 3 seconds. 1
- The display shows the last error in memory; any button or power clears it. 1
- E62 is wash temperature too high, E23 a drain triac error, E13 a water leak in the tub or pressure sensor. 1
- The Owner Center treats E35 and E42 as shown, while the sheet marks them as not shown. 123
- Demo Mode uses the same two buttons within the first 10 seconds. 1
Why does my Electrolux washer stop without showing a code?#
Because most codes are stored, not shown. The technician sheet has a Display Notification column, and only a short list of codes says yes. A washer that stops on any other code can look as if nothing happened. 1
The shown list is short: 11, 21 and 41, the board codes 91, 93, 94, 97 and 9C, the power codes H1/B1, H2/B2 and H3/B3, and F2 for too much soap. 1 Everything else, from the pressure sensor rows to the heater rows, has the answer "No".
That matters when you call us. "It just stopped" is a very different story from "it stopped and the last stored code was 62". The stored code costs you less than a minute to read.
How do I recall the last error code?#
Power the washer on, wait at least 10 seconds, then hold temp and select (set) together for 3 seconds. The display shows the last error in memory. Touch any button, or press power, to clear the display and return to normal. 1
- 1
- 2
- 3
- 4
- 5

The sheet covers the 300, 400, 500 and 600 series of 2018 and describes both push-button and rotary-dial models. On some washers the cycle choice differs, so if your panel looks different from the sheet, say so when you book. 1
Which codes are hidden?#
Most of them. The ones owners ask about are E13, E23, E31 and E62, along with their neighbors in the pressure, drain, door and temperature groups. The sheet gives the meaning and sends the technician to a numbered test. 1
| Code | What the sheet says | Shown? |
|---|---|---|
| 13 | Water leak in tub or in pressure sensor | No 1 |
| 23 | Drain triac error | No 1 |
| 24 | Drain triac error sensing | No 1 |
| 31 | Electronic pressure switch error | No 1 |
| 32 | Pressure sensor calibration problem | No 1 |
| 35 | Pressure sensor indicates water overfill | No 1 |
| 42 to 45 | Door lock device, door lock triac, door closed sensing, line door sensing | No 1 |
| 62 | Wash temperature too high | No 1 |
| 74 | Wash temperature does not increase | No 1 |
The sheet prints these as bare numbers. The Owner Center writes E11, E21, E35, E41 and E42 with an E, and our pages do too. Each hidden code has a page: E13, E23, E31, E32 and E62.
What can I do about the hidden codes?#
Very little, and that is the point. For E13, E23, E31 and E62 the sheet's next step is a technician test: a pressure test, a drain test or a temperature test. The reading step is the useful part for an owner. 1
Look at the pairs. E21 is the shown row for water that is not pumping out fast enough. E23 and E24, the drain triac and its sensing, are hidden. They are separate rows, so a stored E23 is not an E21 in disguise. 1 The washer drain pump entry shows the part involved.
E62 and E74 are the temperature pair. E62 is too high and E74 is a temperature that does not rise. 1 If the recall shows 62, do not run more cycles to find out why.
Which hidden codes do have an owner step?#
Three rows do. The sheet's next-step column for E55 asks you to check for a heavy or unbalanced load. For F5, load unbalanced, it says to redistribute the load and restart. For F9, hot and cold hoses reversed, it says to reverse the hoses. 1
F9 is also the washer-side cousin of the hose problem on the Owner Center's HO SE page. Our water supply and hoses guide covers it. F5 and F9 are marked as not shown too, so a recall is how you would find them.
What do the shown codes tell you?#
The shown codes are the ones the washer wants you to act on. Each has a plain meaning on the sheet, and a few have a first step an owner can take. 14
- 11 is fill time too long. The Owner Center ties it to hot and cold lines being reversed, and to the water supply requirements. 14
- 21 is water not pumping out fast enough. 1
- 41 is the control board thinking the door switch is open. 1
- F2 is excess detergent or the wrong kind, and the sheet's advice is to reduce the detergent or change to a high efficiency type. 1
- H1/B1, H2/B2 and H3/B3 are power supply limits: frequency out of limits or incoming voltage too high. 1
Our detergent and suds guide picks up F2 and the SU dS message.
What about E35 and E42?#
The Owner Center treats both as codes you can see, while the sheet marks both as not shown. Both documents are Electrolux's, so we show both wordings and do not pick a side. 123
For E35 the Owner Center says the pressure sensor is indicating a water overfill, calls it a known installation issue, and gives two steps: press cancel to make E35 disappear and then press start to resume, or perform a hard reset by disconnecting the power cord, reconnecting it and restarting the cycle. 2
For E42 it says the door lock is not being recognized and lists four checks: the door is fully closed, nothing is keeping it from closing, you hear a click when it shuts, and the latch and striker are working. 3

Because the two documents disagree about whether these codes show, the recall is a good tiebreaker. If you recalled E35 or E42, you have your answer.
Does the E11 lock matter here?#
E11 is shown, but its note helps explain "dead" washers. The Owner Center says E11 may lock the unit for up to 6 minutes, and that unplugging and re-plugging restarts the 6-minute lock. 4 So if the washer is silent after a fill problem, the lock may simply be running. Give it the time.
How soon after a stop should I recall the code?#
The sheet gives no time limit, and it describes the code as the last error in memory. 1 Recall it before you run another cycle, because a new error may replace the one you want. A note of the code, the cycle that was running and roughly how far into it the washer stopped is the most useful handover to a technician.
Is the recall the same as Demo Mode?#
No, but they share two buttons, which is a trap. Demo Mode is entered within 10 seconds of powering on, after selecting a particular cycle, by holding temp and select for 3 seconds. Recall waits at least 10 seconds first. 1
The sheet says Demo Mode is automatically recalled each time the machine is turned on once it has been activated, and that unplugging does not clear it. 1 A washer in Demo Mode flashes a message three times at start-up and simulates cycles on the display only. If you think you entered it by mistake, the sheet's exit sequence is to select the Delicates cycle, press start and then cancel, power the unit off and on again, and hold temp and select. 1
When in doubt, switch the washer off and begin again. The timing is the whole difference.
See the washer repair page for what a visit covers.
Sources#
- Washer Tech Data Sheet, A11200302 (1803)Electrolux (technician sheet; retailer-hosted copy) · A11200302 (1803); 2018, 300/400/500/600 series (EFLS527UTT and EFLS627UTT copies are byte-identical) · pp. 2-4 (Diagnostic Mode, Demo Mode, Recalling Last Error Code, Washer Error Codes)
- Laundry front loading washer displaying Error Code E35 pressure sensor indicates water overfill. (KB 1820074)Electrolux / Owner Center knowledge base (owner.electrolux.com) · Knowledge-base page text saved 10.11.2026; no edition is printed on the page · article text
- Laundry front loading washer displaying Error Code E42 door lock device failure. (KB 1829258)Electrolux / Owner Center knowledge base (owner.electrolux.com) · Knowledge-base page text saved 10.11.2026; no edition is printed on the page · article text
- Laundry front loading washer displaying Error Code E11 long fill time. (KB 1820068)Electrolux / Owner Center knowledge base (owner.electrolux.com) · Knowledge-base page text saved 10.11.2026; no edition is printed on the page · article text


