Electrolux washer E13 / Leak

Electrolux washer
error E13

Washer / display reference

E13 on an Electrolux front-load washer means water is leaking in the tub or the pressure-sensor line. The sheet does not show it on the display. Shut the taps, unplug the washer if water is escaping, and book a technician.

Also shown as E13

Last reviewed

Washer / display reference
Meaning
E13 on an Electrolux front-load washer means water is leaking in the tub or the pressure-sensor line. The sheet does not show it on the display. Shut the taps, unplug the washer if water is escaping, and book a technician.
Who handles it
Technician — close the water supply
Related codes
Source
Washer Tech Data Sheet, A11200302 (1803)

What Electrolux washer E13 means.

What it means

E13 on an Electrolux front-load washer means water is leaking in the tub or the pressure-sensor line. The sheet does not show it on the display. Shut the taps, unplug the washer if water is escaping, and book a technician.

What you can safely check

Water and electricity do not mix.

When to call a technician

There is any water on the floor, or E13 comes back after you have checked the hoses and door seal.

Your checklist, kept on this device

Safe checks, in order.

0 of 5 checks done
  1. Electrolux washer E13: Washers in a thoughtfully designed home
    Illustration. Follow your model’s instructions.
    Before you begin

    Stop the water first

    If you see water on the floor, close both supply taps and pull the plug before you touch anything else. Mop it up so you can tell whether it is still running.

  2. A dark glass touch panel on a white front-load dryer, the display unlit
    Illustration. Follow your model’s instructions.
    Check 2

    Look for a leak you can see

    Check the fill hoses, the drain hose connection and the front door seal for drips. Test 2 on the sheet begins with the question of whether the washer is leaking at all.

  3. Technician in navy coveralls holding a tablet with a blank checklist, a washer in the background.
    Illustration. Follow your model’s instructions.
    Check 3

    Do not open the sensor line

    The pressure sensor is fed by a small air line. The sheet lists an air leak there as a cause, so leave the line in place and have it inspected rather than pulling it off.

  4. A technician inspecting a front-load washer pump filter
    Illustration. Follow your model’s instructions.
    Check 4

    Recall the stored code

    With the washer on, wait about ten seconds and press and hold Temp plus Select for three seconds. The display shows the last error in memory, which tells you whether E13 was the latest event.

  5. Illustration. Follow your model’s instructions.
    Check 5

    Book a visit

    Fixing a leak in the tub or in the sensor system, or replacing the sensor and then the main board, needs a technician. Tell us the model and when you first saw water.

Still showing E13?

Send us the model and the checks you have done, and open your request here.

Book a visit

Fill and the water level.

Conceptual Washer sectionInlet valveTubLevel sensorDrain pump1234
  1. 1Inlet valve
  2. 2Tub

A simplified drawing, since layouts differ between models. Pick an outlined part for its photo and the related check.

Parts behind the message.

Round pressure switch with a clear air tube attached, lying on a wood counter beside a coiled gray hose.

Component reference

Washer pressure sensor

The pressure sensor tells the washer how high the water stands in the tub.

Read the definition

A little more context.

What does E13 mean on this washer?

The control found water in the tub or in the pressure-sensor system where it should not be. The sheet's wording is water leak in tub or in pressure sensor, and it marks the code as not shown to the user.

Read the supporting manual

How does a technician work through E13?

Test 2 asks if the washer is leaking, then whether the sensor's air path leaks, then replaces the pressure sensor, and only after that the main control board.

Read the supporting manual

Is it safe to run the washer with E13?

No. If water is escaping, stop the cycle, close the taps and unplug the washer. Standing water near a mains-powered machine is a shock risk as well as a floor-damage risk.

Read the supporting manual

How is E13 different from E35?

E13 points to water where it should not be. E35 means the pressure sensor reads an overfill, and the Owner Center treats it as a continuous-fill problem you can try a hard reset on.

Read the supporting manual

The manual behind the message.

Manufacturer document

Washer Tech Data Sheet, A11200302 (1803)

Electrolux (technician sheet; retailer-hosted copy)

A11200302 (1803); 2018, 300/400/500/600 series (EFLS527UTT and EFLS627UTT copies are byte-identical) / p.1 (Washer Error Codes)

Row 13 of the 2018 front-load washer sheet (the washer sheet). The sheet marks E13 as not displayed; it surfaces through stored-code recall or a stopped cycle.

Here to help

Good questions.
Clear answers.

Talk to our team
Why do I not see E13 on the display?

The sheet marks E13 as not displayed. You may only notice a stopped cycle or a puddle, and recall the code from memory afterward.

Could E13 be a leak that is not on the floor?

Yes. The sheet also names the pressure-sensor system, so the leak may be an air leak in the sensing line rather than water you can see.

Will cleaning the filter fix E13?

The sheet does not list that. It lists a leak check, the sensor's air path, then the sensor and the board.

Can I reset E13 by unplugging?

A reset only clears the message. If water or an air leak is still there the code will come back, so find the leak first.

Let’s take care of it.

Premium appliances deserve
careful service.