Electrolux washer E35 / Water level

Electrolux washer
error E35

Washer / display reference

E35 on an Electrolux front-load washer means the pressure sensor reads water overfill. Press Cancel to clear it, restart the cycle, and if it recurs unplug the washer, reconnect and let the cycle end. If water keeps running, shut the tap and book a visit.

Also shown as E35

Last reviewed

Washer / display reference
Meaning
E35 on an Electrolux front-load washer means the pressure sensor reads water overfill. Press Cancel to clear it, restart the cycle, and if it recurs unplug the washer, reconnect and let the cycle end. If water keeps running, shut the tap and book a visit.
Who handles it
Owner checks first, then a technician
Related codes
Source
Washer Tech Data Sheet, A11200302 (1803)

What Electrolux washer E35 means.

What it means

E35 on an Electrolux front-load washer means the pressure sensor reads water overfill. Press Cancel to clear it, restart the cycle, and if it recurs unplug the washer, reconnect and let the cycle end. If water keeps running, shut the tap and book a visit.

What you can safely check

If water is rising or leaking, turn the taps off and pull the plug when you can do so safely.

When to call a technician

Water keeps filling, E35 returns after a hard reset, or the tub spills.

Your checklist, kept on this device

Safe checks, in order.

0 of 5 checks done
  1. Electrolux washer E35: Gloved hand holding a round pressure switch with wires and a thin clear tube over an open washer tub; the unplugged cord rests on the cabinet
    Illustration. Follow your model’s instructions.
    Before you begin

    Shut the taps if water keeps coming in

    Continuous fill is the Owner Center's own symptom for E35. Close both taps and unplug before you do anything else.

  2. Washers in a thoughtfully designed home
    Illustration. Follow your model’s instructions.
    Check 2

    Press Cancel and restart

    Electrolux says Cancel makes E35 disappear from the display. Press Start again to resume the cycle.

  3. A dark glass touch panel on a white front-load dryer, the display unlit
    Illustration. Follow your model’s instructions.
    Check 3

    Do a hard reset

    Unplug the power cord, plug it in again, wait a couple of seconds until the cycle ends or beeps, then restart the cycle.

  4. Technician in navy coveralls holding a tablet with a blank checklist, a washer in the background.
    Illustration. Follow your model’s instructions.
    Check 4

    Think about installation

    The article calls E35 a known installation issue. If the washer was recently installed or moved, the installer should check it.

  5. A technician inspecting a front-load washer pump filter
    Illustration. Follow your model’s instructions.
    Check 5

    Book a visit

    Test 5 on the sheet chases a stuck inlet valve, a clogged air trap and the sensor. That needs a technician.

Still showing E35?

Send us the model and the checks you have done, and open your request here.

Book a visit

Fill and the water level.

Conceptual Washer sectionInlet valveTubLevel sensorDrain pump1234
  1. 1Inlet valve
  2. 2Tub

A simplified drawing, since layouts differ between models. Pick an outlined part for its photo and the related check.

Parts behind the message.

Round pressure switch with a clear air tube attached, lying on a wood counter beside a coiled gray hose.

Component reference

Washer pressure sensor

The pressure sensor tells the washer how high the water stands in the tub.

Read the definition

A little more context.

What does E35 mean?

The control thinks the tub holds too much water. Electrolux's article says the pressure sensor indicates overfill, and the symptom it lists is water that runs continuously.

Read the supporting manual

What can I do myself?

Cancel the message, restart the cycle, and if needed do the hard reset in the article. Close the taps first when water will not stop.

Read the supporting manual

What does a technician test?

Test 5 asks if the level is above 4.5 inches, whether water keeps entering, whether it stops with power removed, then checks the air trap, valve wiring and the sensor.

Read the supporting manual

Is E35 an urgent leak risk?

Potentially. An inlet that does not close can overfill the tub and spill. Do not leave a washer with E35 running while you are out.

Read the supporting manual

The manual behind the message.

Manufacturer document

Washer Tech Data Sheet, A11200302 (1803)

Electrolux (technician sheet; retailer-hosted copy)

A11200302 (1803); 2018, 300/400/500/600 series (EFLS527UTT and EFLS627UTT copies are byte-identical) / p.1 (Washer Error Codes)

Manufacturer document

Laundry front loading washer displaying Error Code E35 pressure sensor indicates water overfill. (KB 1820074)

Electrolux / Owner Center knowledge base (owner.electrolux.com)

Owner Center article, cached 10.11.2026 (no edition date printed) / article text

Row 35 of the 2018 front-load washer sheet (the washer sheet) and Owner Center article 1820074. Not shown on the sheet's display column.

Here to help

Good questions.
Clear answers.

Talk to our team
Does E35 mean my washer is flooding?

It means the control believes the water is too high. Check the floor and the tub, and shut the taps if water keeps entering.

Does unplugging clear E35?

Electrolux recommends a hard reset, then restarting the cycle. If the sensor or valve is the problem, E35 returns.

Who handles E35 within 30 days?

The installer, per the article. After that, book with us.

Is E35 the same as E38?

No. E38 is a clogged air trap, a different row in the same test.

Let’s take care of it.

Premium appliances deserve
careful service.