Read the whole display
Write down the full display text. The sheet says to press Power, wait 10 seconds, then hold Temp and Select (Set) together for 3 seconds to see the last stored error.
Model-specific code library
Electrolux's 2018 washer sheet decodes about fifty codes, and Owner Center articles add E11, E21, E35, E41, E42, HO SE, LOC and SU dS. We decode only what these documents print.
E21 on an Electrolux front-load washer means the water is not pumping out fast enough. Check the drain hose for a kink first, then confirm the hot and cold lines and the hose installation. If it persists, book a technician.
Read the E21 checks58 researched washer codes. A code can mean different things on different models, so read your own manual.
E83 is a wrong selector reading on Electrolux's 2018 washer sheet: the control read the cycle selector in a position it does not recognize. The display does not show E83. Turn the selector once and book a technician if it returns.
TechnicianE86 on Electrolux's 2018 washer sheet is an incorrect user interface selection table: the control panel and main board disagree about the available options. The display does not show E86. Book a technician; the sheet checks the panel wiring.
TechnicianElectrolux's washer sheet reads E55 as motor under speed: the drum is turning more slowly than the control asked. It appears on select models and not on 300 series. Check for a heavy or unbalanced load first, then book a technician.
TechnicianE57 is high current on the inverter, the motor control, in Electrolux's 2018 washer sheet. The display does not show E57. Unplug the washer, reduce an overloaded drum if you can, and book a technician for the motor tests.
TechnicianE62 on the 2018 Electrolux washer sheet means the wash temperature went too high. The display does not show E62. Stop the cycle, unplug the washer and book a technician; the sheet sends it to the temperature sensor and heater tests.
TechnicianE68 means current is leaking to ground from the heater or its wiring, per the 2018 Electrolux washer sheet, for select models. The display does not show E68. Unplug the washer, do not run it again, and book a technician.
TechnicianE41 on an Electrolux front-load washer means the control thinks the door switch is open. Check the door is fully closed, nothing is caught in it, and you hear a click. The latch and striker must work. If it persists, book a technician.
Owner checks firstE42 on an Electrolux front-load washer means the door lock is not being recognized. Make sure the door is fully closed, nothing is in the way, you hear a click, and the latch and striker work. If not, book a technician.
Owner checks firstE31 on an Electrolux front-load washer is an electronic pressure switch error on the technician sheet, and the display does not show it. Owners have no safe fix beyond reading the stored code, so book a technician.
TechnicianE32 on an Electrolux front-load washer is a pressure sensor calibration problem on the technician sheet. The display does not show E32. Book a technician; the sheet gives no owner steps beyond reading the stored code.
TechnicianE35 on an Electrolux front-load washer means the pressure sensor reads water overfill. Press Cancel to clear it, restart the cycle, and if it recurs unplug the washer, reconnect and let the cycle end. If water keeps running, shut the tap and book a visit.
Owner checks firstE38 on an Electrolux front-load washer means the air trap is clogged. The display does not show E38. Book a technician; the air trap sits behind the tub with the pressure sensor, and the sheet lists no owner step.
TechnicianE11 on an Electrolux front-load washer means the fill took too long, so water is not arriving fast enough. Check that both taps are open and the hot and cold hoses sit on the right inlets. The washer may stay locked for up to 6 minutes.
Owner checks firstF9 is a hot valve warning on Electrolux's 2018 washer sheet: the hot and cold water hoses are reversed. The sheet says to switch the hoses to reduce water-temperature problems. The display does not show F9. Close the taps before you swap them.
Owner checks firstHO SE flashing on an Electrolux front-load washer means the hot and cold inlet hoses are reversed. Close both taps, press Cancel, and connect each hose to the correct inlet. If the washer was installed in the past 30 days, call the installer.
Owner checks firstE21 on an Electrolux front-load washer means the water is not pumping out fast enough. Check the drain hose for a kink first, then confirm the hot and cold lines and the hose installation. If it persists, book a technician.
Owner checks firstE23 on an Electrolux front-load washer is a drain triac error on the technician sheet. The display does not show E23. Owners can check the drain hose, but the sheet's next steps are electrical, so book a technician if the washer will not drain.
TechnicianE24 on an Electrolux front-load washer is the drain triac sensing row. The control cannot confirm the switching that runs the drain pump. It is not shown on the display, so check the drain hose and book a technician.
TechnicianE84 is a recirculation pump triac sensing failure that stops the cycle, on Electrolux's 2018 washer sheet (select models). The display does not show E84. The sheet's next step is to replace the main board, so book a technician.
TechnicianE85 is a recirculation pump triac alarm that stops the cycle, on Electrolux's 2018 washer sheet, for select models. The display does not show E85. Book a technician; the sheet checks the pump wiring, the pump and then the board.
TechnicianE88 is a concentrated wash pump triac alarm on Electrolux's 2018 washer sheet, for select models. The display does not show E88. Book a technician; the sheet checks the pump's wiring, the pump and then the main board.
TechnicianH1 or B1 means the power frequency is out of limits, per Electrolux's 2018 washer sheet. The display shows it. Unplug the washer and book a technician; the sheet has the supply checked under load before any board is replaced.
Model-dependent / read firstH2 or B2 means the supply voltage is too high, according to Electrolux's 2018 washer sheet. The display shows it. Unplug the washer and book a technician; the sheet has the incoming voltage checked under load first.
Model-dependent / read firstH3 or B3 is listed as supply voltage too high, the same wording as H2/B2, on Electrolux's 2018 washer sheet. The display shows it. Unplug the washer and book a technician; test 18 checks the supply under load first.
Model-dependent / read firstEF2 is how owners write F2, the washer sheet's too much soap or wrong detergent type code. No Electrolux document prints it with an E. Use less detergent, make sure it is high efficiency, and run a rinse. The display shows it.
Owner checks firstSU dS means the washer detected too many suds and will run extra rinses until they clear, about 5 minutes each. Use high-efficiency detergent, use less of it, and run an empty quick wash to clean the unit. Press Cancel to clear the alert.
Owner checks firstThe sheet prints codes without the E (11, 21, F2, F5), so EF2 and EF5 are owner spellings. It marks some codes as not shown while an article treats them as visible. E10, E12, E20, E22, E25, E40, E50, E60, E61, EC1, EF1 and EF4 appear in none of our documents.

Electrolux's 2018 washer sheet decodes about fifty codes, and Owner Center articles add E11, E21, E35, E41, E42, HO SE, LOC and SU dS. We decode only what these documents print.
The sheet prints codes without the E (11, 21, F2, F5), so EF2 and EF5 are owner spellings. It marks some codes as not shown while an article treats them as visible. E10, E12, E20, E22, E25, E40, E50, E60, E61, EC1, EF1 and EF4 appear in none of our documents.
Write down the full display text. The sheet says to press Power, wait 10 seconds, then hold Temp and Select (Set) together for 3 seconds to see the last stored error.
If water escapes, turn off the taps and pull the plug. Leak, heater and motor control codes are not owner repairs and need a technician.
A washer that will not spin is most often reacting to an unbalanced or heavy load, a machine that is out of level, or a door that is not locked. Electrolux's sheet ties the motor-speed codes E55 and E59 to the motor, belt, tub bearings and motor control board.
Dispenser trouble on an Electrolux front loader usually comes from the wrong detergent, too much of it, a drawer that is not seated or buildup in the compartments. Detergent packs belong in the drum, not the drawer.
Electrolux's text articles give no step-by-step answer for washer odors; its cleaning and care guide is a video. What the written articles do offer are habits that go with a clean machine: the right detergent in the right amount, a wiped door seal and an empty cleaning run after suds.
Follow the guide for your exact model. Consult how we research these pages.
The sheet prints codes without the E (11, 21, F2, F5), so EF2 and EF5 are owner spellings. It marks some codes as not shown while an article treats them as visible. E10, E12, E20, E22, E25, E40, E50, E60, E61, EC1, EF1 and EF4 appear in none of our documents.
Photograph the entire washer display along with the model label. Note what the appliance was doing as the message came up, and do not lean on an explanation meant for a different appliance.
An older search phrase is no evidence from the maker. If our washer manuals leave a message unexplained, we keep its name and direct you to help, without guessing a part or a cause.
Open the washer manuals kept in this library and match the models on their covers to your label. A model that differs has its own operating guide.