Electrolux washer E21 / Drain

Electrolux washer
error E21

Washer / display reference

E21 on an Electrolux front-load washer means the water is not pumping out fast enough. Check the drain hose for a kink first, then confirm the hot and cold lines and the hose installation. If it persists, book a technician.

Also shown as E21

Last reviewed

Washer / display reference
Meaning
E21 on an Electrolux front-load washer means the water is not pumping out fast enough. Check the drain hose for a kink first, then confirm the hot and cold lines and the hose installation. If it persists, book a technician.
Who handles it
Owner checks first, then a technician
Related codes
Source
Washer Tech Data Sheet, A11200302 (1803)

What Electrolux washer E21 means.

What it means

E21 on an Electrolux front-load washer means the water is not pumping out fast enough. Check the drain hose for a kink first, then confirm the hot and cold lines and the hose installation. If it persists, book a technician.

What you can safely check

Electrolux calls a kinked drain hose the most common cause.

When to call a technician

E21 returns with a straight, clear drain hose, or water stays in the tub after the cycle.

Your checklist, kept on this device

Safe checks, in order.

0 of 5 checks done
  1. Electrolux washer E21: Gloved hand holding the drain pump filter and cap beside the open lower access panel of a washer, with a metal baking tray on a towel on the floor
    Illustration. Follow your model’s instructions.
    Before you begin

    Straighten the drain hose

    Electrolux calls a kinked drain hose the most common cause. Pull the washer out a little, follow the hose and remove any bends or squashed spots.

  2. Washers in a thoughtfully designed home
    Illustration. Follow your model’s instructions.
    Check 2

    Check how the hose ends

    The hose has to be installed the way the Use and Care guide shows, with the free end held at the right height. A hose pushed too far down can drain badly.

  3. A dark glass touch panel on a white front-load dryer, the display unlit
    Illustration. Follow your model’s instructions.
    Check 3

    Confirm hot and cold are not swapped

    The article lists reversed supply hoses beside the drain checks, and says a recent move is the usual reason.

  4. Technician in navy coveralls holding a tablet with a blank checklist, a washer in the background.
    Illustration. Follow your model’s instructions.
    Check 4

    Look at the standing water

    Open the door only if the tub is not full. If water is stuck at the bottom after a cycle, note how high it is and tell us.

  5. A technician inspecting a front-load washer pump filter
    Illustration. Follow your model’s instructions.
    Check 5

    Book a visit

    A blocked or failing pump needs the cabinet opened. Within 30 days of installation, the article sends you to the installer; after that, book with us.

Still showing E21?

Send us the model and the checks you have done, and open your request here.

Book a visit

The washer drain path.

Conceptual Washer sectionPump filterDrain pumpDrain hoseHousehold drain1234
  1. 1Pump filter
  2. 3Drain hose
  3. 4Household drain

A simplified drawing, since layouts differ between models. Pick an outlined part for its photo and the related check.

Parts behind the message.

A little more context.

What does E21 mean?

The pump-out is too slow for the control. The technician sheet reads it as water not pumping out fast enough, and the display shows it.

Read the supporting manual

What do I check first for E21?

The drain hose. Electrolux says a kink is the commonest problem, so straighten it and look for anything restricting the run before you assume the pump is bad.

Read the supporting manual

What does the sheet test after the hose?

Test 3 checks the drain hose for restrictions, then looks for 120 VAC at the pump while a cycle runs. No voltage points to wiring or the board; voltage with no pumping points to a blocked or failed pump.

Read the supporting manual

Is E21 the same as E23 or E24?

No. E23 and E24 are drain triac rows, which are electrical checks on the control board. E21 is the flow-rate row and the one an owner can act on.

Read the supporting manual

The manual behind the message.

Manufacturer document

Washer Tech Data Sheet, A11200302 (1803)

Electrolux (technician sheet; retailer-hosted copy)

A11200302 (1803); 2018, 300/400/500/600 series (EFLS527UTT and EFLS627UTT copies are byte-identical) / p.1 (Washer Error Codes)

Manufacturer document

Laundry front loading washer displaying Error Code E21 long pump out time. (KB 1820072)

Electrolux / Owner Center knowledge base (owner.electrolux.com)

Owner Center article, cached 10.11.2026 (no edition date printed) / article text

Row 21 of the 2018 front-load washer sheet (the washer sheet) and Owner Center article 1820072 for front-load washers.

Here to help

Good questions.
Clear answers.

Talk to our team
Is a kinked hose really the likely cause of E21?

Electrolux says so in its article. It is also the only cause you can check without opening the washer.

Should I run another cycle after clearing a kink?

Yes, a short drain-and-spin cycle shows quickly whether E21 is gone.

Does E21 mean the pump is broken?

Not necessarily. The sheet checks the hose and the pump's power supply before it replaces the pump.

Can too much detergent slow draining?

Electrolux's slow-draining article says too much detergent can inhibit draining, so keep to the recommended amount.

Let’s take care of it.

Premium appliances deserve
careful service.