Electrolux washer E11 / Water supply

Electrolux washer
error E11

Washer / display reference

E11 on an Electrolux front-load washer means the fill took too long, so water is not arriving fast enough. Check that both taps are open and the hot and cold hoses sit on the right inlets. The washer may stay locked for up to 6 minutes.

Also shown as E11

Last reviewed

Washer / display reference
Meaning
E11 on an Electrolux front-load washer means the fill took too long, so water is not arriving fast enough. Check that both taps are open and the hot and cold hoses sit on the right inlets. The washer may stay locked for up to 6 minutes.
Who handles it
Owner checks first, then a technician
Related codes
Source
Washer Tech Data Sheet, A11200302 (1803)

What Electrolux washer E11 means.

What it means

E11 on an Electrolux front-load washer means the fill took too long, so water is not arriving fast enough. Check that both taps are open and the hot and cold hoses sit on the right inlets. The washer may stay locked for up to 6 minutes.

What you can safely check

Electrolux says E11 can lock the washer for up to 6 minutes, and pulling the plug starts that count over.

When to call a technician

E11 returns after the taps, hoses and a six-minute wait, or water is dripping from a fill hose.

Your checklist, kept on this device

Safe checks, in order.

0 of 5 checks done
  1. Electrolux washer E11: Hand pointing at a red-handled shut-off valve on a tiled wall, with two braided hoses running to the red and blue inlets on the back of a washer
    Illustration. Follow your model’s instructions.
    Before you begin

    Leave it plugged in and wait

    Electrolux says E11 can lock the washer for up to 6 minutes, and pulling the plug starts that count over. Let it sit for the full six minutes before you try anything else.

  2. Washers in a thoughtfully designed home
    Illustration. Follow your model’s instructions.
    Check 2

    Open both water taps all the way

    A half-open tap slows the fill enough to trip this row. Turn each tap fully on, then press Cancel and start a short cycle.

  3. A dark glass touch panel on a white front-load dryer, the display unlit
    Illustration. Follow your model’s instructions.
    Check 3

    Match the hoses to the inlets

    Hot supply belongs on the hot inlet and cold supply on the cold inlet. The Owner Center calls swapped hoses a known installation issue, especially on a washer that was recently moved.

  4. Technician in navy coveralls holding a tablet with a blank checklist, a washer in the background.
    Illustration. Follow your model’s instructions.
    Check 4

    Look for kinks behind the washer

    With the taps shut and the plug out, pull the washer forward a little and check the two fill hoses for sharp bends or a crushed section. Straighten them and reconnect.

  5. A technician inspecting a front-load washer pump filter
    Illustration. Follow your model’s instructions.
    Check 5

    Book a visit if E11 returns

    If the taps, hoses and a fresh cycle do not clear it, the next steps on the sheet are inlet-valve and pressure-sensor work. That needs a technician.

Still showing E11?

Send us the model and the checks you have done, and open your request here.

Book a visit

Water into the washer.

Conceptual Washer sectionSupply valveInlet hoseTub inlet123
  1. 1Supply valve
  2. 2Inlet hose
  3. 3Tub inlet

A simplified drawing, since layouts differ between models. Pick an outlined part for its photo and the related check.

Parts behind the message.

Round pressure switch with a clear air tube attached, lying on a wood counter beside a coiled gray hose.

Component reference

Washer pressure sensor

The pressure sensor tells the washer how high the water stands in the tub.

Read the definition

A little more context.

What does E11 mean on an Electrolux washer?

The washer did not get water during the wash phase of the cycle. The technician sheet reads it as fill time too long, and it is one of the few codes the sheet says the display shows.

Read the supporting manual

Why does the washer stay locked after E11?

Electrolux says the washer can lock for up to 6 minutes after E11. Unplugging and plugging back in restarts that six-minute count, so the quickest route is to leave the power alone.

Read the supporting manual

What does a technician look at if the hoses are right?

The sheet works through clogged inlet screens, a stuck inlet valve and the pressure sensor, then the main board last. We carry out that sequence on a visit, not as an owner job.

Read the supporting manual

Who deals with E11 on a new washer?

For a washer installed in the past 30 days, Electrolux sends you back to your installer. After that window, book a visit with us and give us the model label and what the display showed.

Read the supporting manual

The manual behind the message.

Manufacturer document

Washer Tech Data Sheet, A11200302 (1803)

Electrolux (technician sheet; retailer-hosted copy)

A11200302 (1803); 2018, 300/400/500/600 series (EFLS527UTT and EFLS627UTT copies are byte-identical) / p.1 (Washer Error Codes)

Manufacturer document

Laundry front loading washer displaying Error Code E11 long fill time. (KB 1820068)

Electrolux / Owner Center knowledge base (owner.electrolux.com)

Owner Center article, cached 10.11.2026 (no edition date printed) / article text

Row 11 of the 2018 front-load washer sheet (the washer sheet, 300 to 600 series), plus Owner Center article 1820068. The sheet lists E11 among the codes shown on the display.

Here to help

Good questions.
Clear answers.

Talk to our team
How long does E11 lock the washer?

Up to 6 minutes, according to the Owner Center article. If you unplug the washer during that time the lock timer begins again.

Can swapped hoses really cause E11?

Yes, they are on Electrolux's own list. Hot supply must reach the hot inlet and cold supply the cold inlet, and a washer that was moved is the usual suspect.

Is low water pressure part of the E11 checks?

Yes. The technician test asks whether incoming pressure is above 20 psi and whether the inlet screens are clean or the hoses blocked.

Does E11 mean the inlet valve is broken?

Not by itself. The sheet checks flow, taps, hoses and screens first and only then moves to the valve, so the code points to a slow fill, not a named part.

What should I tell you when I book for E11?

The model number, when the washer was installed or moved, and whether the taps were fully open. That lets the visit start at the right test.

Let’s take care of it.

Premium appliances deserve
careful service.