Independent appliance repair

Electrolux washer repair, with care.

We repair Electrolux washers that won’t drain, won’t start, leak, shake or show an E, EF or door code. Tell us the code and what the washer does, then book a technician.

Washers in a thoughtfully designed home
Independent service. Considered care.
Experienced techniciansWarranty on our workmanshipOEM parts available on orderUpfront pricing, agreed before work
WashersDryersWall ovensRefrigeratorsDishwashersCooktopsFreezersMicrowavesRangesWine coolersBeverage centersError code helpWarranty on our workmanship

When your washer needs attention.

Symptom

Electrolux washer not spinning

A washer that will not spin is most often reacting to an unbalanced or heavy load, a machine that is out of level, or a door that is not locked. Electrolux's sheet ties the motor-speed codes E55 and E59 to the motor, belt, tub bearings and motor control board.

Symptom

Electrolux washer detergent dispenser problems

Dispenser trouble on an Electrolux front loader usually comes from the wrong detergent, too much of it, a drawer that is not seated or buildup in the compartments. Detergent packs belong in the drum, not the drawer.

Symptom

Electrolux washer smells bad

Electrolux's text articles give no step-by-step answer for washer odors; its cleaning and care guide is a video. What the written articles do offer are habits that go with a clean machine: the right detergent in the right amount, a wiped door seal and an empty cleaning run after suds.

Symptom

Electrolux washer not filling with water

A front loader that fills slowly or not at all is usually short of water at the inlet: a closed faucet, reversed hoses, a kinked hose or a clogged inlet filter. Electrolux's E11 means the washer is not filling during the wash phase.

Symptom

Electrolux washer leaking water

Work out the source of the water first. Electrolux sorts front-load leaks into four spots: the inlet hoses, the drain hose, the door seal and the dispenser drawer. Each has its own quick check, and a leaking tub or sensor shows as E13.

Symptom

Electrolux washer drum not turning

When the drum does not turn during a cycle, the sheet looks at the motor and its control: codes E57, E58, E59 and E5A to E5F. A door that is not closed, a heavy load or a low supply voltage can mimic the problem, so rule those out.

Symptom

Electrolux washer shaking or banging

Violent shaking is usually a load that is off balance or a washer that is not resting level on a solid floor. Electrolux's noise guide adds shipping bolts, stacking hardware and a drain hose that slaps the cabinet.

Symptom

Electrolux washer not draining

A washer that is slow to empty is most often fighting a kinked or poorly installed drain hose. Electrolux's E21 means water is not pumping out fast enough, and the sheet ties E21, E23 and E24 to the drain pump circuit.

A message on the display?

E11Owner checks first

Water supply

E11 on an Electrolux front-load washer means the fill took too long, so water is not arriving fast enough. Check that both taps are open and the hot and cold hoses sit on the right inlets. The washer may stay locked for up to 6 minutes.

E13Close water / technician

Leak

E13 on an Electrolux front-load washer means water is leaking in the tub or the pressure-sensor line. The sheet does not show it on the display. Shut the taps, unplug the washer if water is escaping, and book a technician.

E21Owner checks first

Drain

E21 on an Electrolux front-load washer means the water is not pumping out fast enough. Check the drain hose for a kink first, then confirm the hot and cold lines and the hose installation. If it persists, book a technician.

E35Owner checks first

Water level

E35 on an Electrolux front-load washer means the pressure sensor reads water overfill. Press Cancel to clear it, restart the cycle, and if it recurs unplug the washer, reconnect and let the cycle end. If water keeps running, shut the tap and book a visit.

E41Owner checks first

Door

E41 on an Electrolux front-load washer means the control thinks the door switch is open. Check the door is fully closed, nothing is caught in it, and you hear a click. The latch and striker must work. If it persists, book a technician.

E42Owner checks first

Door

E42 on an Electrolux front-load washer means the door lock is not being recognized. Make sure the door is fully closed, nothing is in the way, you hear a click, and the latch and striker work. If not, book a technician.

EF2Owner checks first

Suds

EF2 is how owners write F2, the washer sheet's too much soap or wrong detergent type code. No Electrolux document prints it with an E. Use less detergent, make sure it is high efficiency, and run a rinse. The display shows it.

EF5Owner checks first

Load balance

EF5 is how owners write F5, the sheet's load unbalanced code. No Electrolux document prints it with an E. Open the door, redistribute the clothes and restart. The display does not show it; a wet bundle or one heavy item is the usual cause.

LOCNo action needed

Settings

LOC on an Electrolux front-load washer is not a failure. It means the control lock is on, which blocks cycles. Scroll to the control lock option and press Select to turn it off. Washer cycles will not run while it is on.

HO SEOwner checks first

Water supply

HO SE flashing on an Electrolux front-load washer means the hot and cold inlet hoses are reversed. Close both taps, press Cancel, and connect each hose to the correct inlet. If the washer was installed in the past 30 days, call the installer.

SU dSOwner checks first

Suds

SU dS means the washer detected too many suds and will run extra rinses until they clear, about 5 minutes each. Use high-efficiency detergent, use less of it, and run an empty quick wash to clean the unit. Press Cancel to clear the alert.

Describe the cycle.
We handle the rest.

How a repair visit runs.
Measured and clear.

  1. A technician unpacking a diagnostic kit in a laundry room
    1

    Tell us the symptom

    Name the washer, dryer or oven and say what it does. Add the code on the screen if there is one.

  2. A technician inspecting a front-load washer pump filter
    2

    Test the machine

    The technician runs the cycle, checks the parts behind the code and explains the cost before starting.

  3. A quiet laundry room with the drum turning
    3

    Finish and verify

    The part is replaced, a test cycle confirms the fix, and the technician walks you through the result.

Prepare for the washer visit.

  1. 1

    Look up the stored code

    Press Power, wait at least 10 seconds, then hold Temp and Select for 3 seconds. The display shows the last error; touch any button to leave.

  2. 2

    Check the water supply

    The supply faucets must be fully on, with 30 to 120 psi and no more than 10 psi between hot and cold. Hot and cold hoses must go to their matching inlets.

  3. 3

    Look at the drain hose

    A kinked drain hose is the commonest cause of E21. The hose should be secured to the drain, and you can pour a gallon down the standpipe to test for a clog.

  4. 4

    Check the door and its click

    For E41 and E42, close the door fully with nothing in the way, and listen for the click as it latches.

  5. 5

    Use the right detergent

    HE detergent in the right amount, up to the max line. Too many suds, shown as SU dS, add extra rinses of about 5 minutes each.

Leave internal testing to a technician.

Book a technician if a code returns after the supply, hose and door checks, or if the tub holds water.

Book a technician if water leaks from a cracked inlet connector or a damaged drain hose. Electrolux says cracks usually come from over-tightening.

When water is spreading on the floor, close both supply faucets and pull the plug.

The pump, door lock and control boards are work for the technician.

Arrange a diagnostic

Real scope. Clear expectations.

9US metro areas
11Appliance types
161Code explanations

The agreement comes first.

Before work starts

The technician examines the appliance, tells you what the repair involves and agrees the cost with you before opening anything up.

Workmanship coverage

An Electrolux still under its manufacturer warranty goes to Electrolux for covered repairs. Our repairs carry a warranty on our workmanship.

Here to help

Good questions.
Clear answers.

Talk to our team
Why does my Electrolux washer show E21?

E21 means water is not pumping out fast enough. Check for a kinked drain hose first, then that the hoses are on the right inlets. Should it come back, a technician can test the pump.

What does E41 or E42 mean?

E41 means the board thinks the door switch is open; E42 means the door lock is not recognized. Close the door fully, clear anything blocking it, and listen for the click. Book a visit if it persists.

Why does my washer shake or knock?

Electrolux lists an unbalanced load, an unlevel washer, shipping bolts left in and a loose drain hose. Check those; if the noise carries on, we can come out.

Does the washer always show its error codes?

No. The sheet marks most codes as seen only in the stored-error recall, and E11, E21, E41 and a few others as shown. If the display is blank but the washer misbehaves, book a visit.

Is the repair covered by the Electrolux warranty?

If your unit is under the manufacturer’s warranty, the manufacturer handles that repair.

Let’s take care of it.

Premium appliances deserve
careful service.