Start from the symptom
Electrolux washer smells bad.
Electrolux's text articles give no step-by-step answer for washer odors; its cleaning and care guide is a video. What the written articles do offer are habits that go with a clean machine: the right detergent in the right amount, a wiped door seal and an empty cleaning run after suds.

Start with safe observations.
Power the appliance down and pull the plug before any owner check. Beware of standing water and sharp debris. Never touch a wet plug or electrical area, take off service panels, or step beyond your model’s owner guide.
- 1
Use the care video
Electrolux publishes How to Clean & Care for Your Front Load Washer (KB 1853590) as a video. Watch it on the Owner Center for the model-specific steps; the written page has no text.
- 2
Wipe the door seal and glass
In its leak article Electrolux says to clean the rubber door seal and the glass to remove hair, dirt, lint and bits of clothing. The article is about leaks, but a clean seal is a sensible first step for odor.
- 3
Measure the detergent
Use high efficiency detergent and stay under the maximum fill line. Too much detergent produces suds that the washer then has to rinse away.
- 4
After an SU dS message
Electrolux says to run an empty cycle on quick wash to clean the unit once the suds problem has been dealt with.
Systems a technician may investigate.
The linked parts are the ones Electrolux’s technician sheets name for this appliance. We confirm each against your model number once the diagnostic is done, and you approve any replacement first.

Washer pressure sensor
The pressure sensor tells the washer how high the water stands in the tub. Electrolux’s washer sheet ties it to E13, E31, E32 and E35. E35 means the sensor reports an overfill; E31 and E32 point at the sensor’s own reading or calibration.

Washer door lock
The door lock keeps the washer closed during a cycle and tells the control the door is shut. Electrolux’s sheet lists five door codes. E41 means the board thinks the door switch is open; E42 and E43 are about the lock itself; E44 and E45 about sensing.

Washer drain pump
The drain pump clears water from the tub. Electrolux’s washer sheet ties E21, E23 and E24 to it: water that pumps out too slowly, and errors in the board’s switching or sensing of the pump. The sheet points them all to one test.
Read the related care guide.

Washer stopped, nothing on the display? Recall the code.
An Electrolux front-load washer shows only some codes. To read the last stored one, power on, wait at least 10 seconds, then hold temp and select for 3 seconds. The display shows the last error in memory. Hidden codes include E13, E23, E31 and E62, and they need a technician.

Detergent left in the drawer? Check the product, the packs and the water.
Electrolux's written sources name no single cause for a drawer that stays full. They list what interferes: a pack in the drawer, detergent above the max fill line, an unseated drawer, buildup, and water that never arrives. Work through these, then book a technician.
When observation becomes a service request.
Leave internal testing to a technician.
If the smell stays after you clean the seal and glass, switch to high efficiency detergent and run an empty cycle, book a visit. Mention whether water stays in the tub after a cycle, and what the odor is like.
Arrange a diagnosticSources and model boundaries.
These sources back the Electrolux washer smells bad guidance. Use the manual for your own model.
- How to Clean & Care For Your Front Load Washer (KB 1853590)
- Laundry front loading washer is leaking water. (KB 1831358)
- Laundry Washers - Detergent Guide (KB 1834689)
- Laundry front loading washer displaying Error Code SU dS too many suds. (KB 1829292)
Follow the guide for your exact model. Consult how we research these pages.
Does Electrolux explain washer odors in writing?
Not in the articles we checked. Its care guide is a video, so we limit this page to the written cleaning facts: seal, detergent amount and an empty run.
Should I clean the door seal?
Electrolux advises cleaning the rubber seal and glass to remove hair, dirt, lint and clothing. It says so in the leak article, and it is a sensible first step for odor.
Can too much detergent cause problems?
It can cause oversudsing. Electrolux says the washer then adds rinses until the suds clear. Use high efficiency detergent and measure it.
What is the empty cycle for?
After SU dS, Electrolux says to run an empty cycle on quick wash to clean the unit. Check your manual for the cleaning cycle available on your model.
Codes, symptoms, parts and service
Link the message to what to do next.
SU dS
SU dS means the washer detected too many suds and will run extra rinses until they clear, about 5 minutes each. Use high-efficiency detergent, use less of it, and run an empty quick wash to clean the unit. Press Cancel to clear the alert.
Electrolux washer not spinning
A washer that will not spin is most often reacting to an unbalanced or heavy load, a machine that is out of level, or a door that is not locked. Electrolux's sheet ties the motor-speed codes E55 and E59 to the motor, belt, tub bearings and motor control board.
Washer repair
Book a diagnostic for your model at the appliance.
Find your metro
Office details and the access information to pass on.