Inside the appliance
Washer drain pump. In plain English.
The drain pump clears water from the tub. Electrolux’s washer sheet ties E21, E23 and E24 to it: water that pumps out too slowly, and errors in the board’s switching or sensing of the pump. The sheet points them all to one test.

Where it fits.
Washer drain pump in the appliance
The documents do not describe where it sits. The sheet has the technician remove the pump to inspect it for blockage, so it is a cabinet-side job.
The image shows the type of component only. It does not select a replacement that fits your model.
What is different once this system needs attention.
Washer drain pump concerns may show up with a drop in performance or a code that keeps returning. Testing comes first before anyone decides the component has failed.
Owner care, within the model instructions.
Power the appliance down and pull the plug before any owner check. Beware of standing water and sharp debris. Never touch a wet plug or electrical area, take off service panels, or step beyond your model’s owner guide.
- 1
Straighten the hose
KB 1820072 says the most common cause of E21 is a kinked drain hose. Test 3 on the sheet also begins by checking the hose for restrictions.
- 2
Verify the setup
The same article asks that hot and cold hoses are not reversed and the drain hose is installed per the use and care manual. After a move, have the installer recheck it.
- 3
Listen
KB 1820062 describes gurgling while draining and a low hum when the drain pump is working. A silent pump with water in the tub is worth reporting.
- 4
Leave the pump to us
The sheet’s next step is a voltage check at the pump, then removing it to look for a blockage. That needs the power off and a technician.
Cleaning or replacement?
Leave internal testing to a technician.
Book a technician if the tub keeps holding water, or if E21, E23 or E24 returns after the hose checks.
Arrange a diagnosticSources and model boundaries.
These sources back the Washer drain pump guidance. Use the manual for your own model.
- Washer Tech Data Sheet, A11200302 (1803)
- Laundry front loading washer displaying Error Code E21 long pump out time. (KB 1820072)
- Laundry Washers Noises Guide (KB 1820062)
Follow the guide for your exact model. Consult how we research these pages.
What does E21 mean?
Water is not pumping out fast enough. Electrolux’s article ties it to the drain hose first, then to hose connections after a recent install.
What do E23 and E24 mean?
E23 is a drain triac error and E24 a drain triac error sensing. A triac is an electronic switch, here the board’s switch for the pump, and the sheet sends both to Test 3.
What does Test 3 involve?
Check the hose for restrictions. Start the washer and look for 120 VAC at the pump. No voltage means wiring, then the main board. Voltage present means the pump is removed, cleared of blockage or replaced.
Is a humming pump normal?
A low hum while the pump runs is listed as normal in KB 1820062. A hum with a full tub that never drains is the time to book a visit.
Codes, symptoms, parts and service
Link the message to what to do next.
E21
E21 on an Electrolux front-load washer means the water is not pumping out fast enough. Check the drain hose for a kink first, then confirm the hot and cold lines and the hose installation. If it persists, book a technician.
Electrolux washer not spinning
A washer that will not spin is most often reacting to an unbalanced or heavy load, a machine that is out of level, or a door that is not locked. Electrolux's sheet ties the motor-speed codes E55 and E59 to the motor, belt, tub bearings and motor control board.
Washer repair
Book a diagnostic for your model at the appliance.
Find your metro
Office details and the access information to pass on.


