What it means
E24 on an Electrolux front-load washer is the drain triac sensing row. The control cannot confirm the switching that runs the drain pump. It is not shown on the display, so check the drain hose and book a technician.
Electrolux washer E24 / Drain
E24 on an Electrolux front-load washer is the drain triac sensing row. The control cannot confirm the switching that runs the drain pump. It is not shown on the display, so check the drain hose and book a technician.
Also shown as E24
E24 on an Electrolux front-load washer is the drain triac sensing row. The control cannot confirm the switching that runs the drain pump. It is not shown on the display, so check the drain hose and book a technician.
The sheet's test begins with restrictions in the hose.
The washer stops with water in the tub, or E24 appears again when you recall the stored code.
Your checklist, kept on this device

The sheet's test begins with restrictions in the hose. Look for kinks behind the washer and for a hose end pushed into a standpipe too far.

Start a short drain-and-spin and listen for the pump. Silence while water sits in the tub is worth telling us.

With the washer on, wait about ten seconds and press and hold Temp plus Select for three seconds. If E24 is shown, you have confirmed the code before the visit.

The pump is on a line-voltage output. Unplug before any cover is lifted and leave the testing to a technician.

Sensing problems on the board output are settled with a meter and, if needed, a new board. Tell us the model and what the tub did.
Send us the model and the checks you have done, and open your request here.
Book a visitA simplified drawing, since layouts differ between models. Pick an outlined part for its photo and the related check.

The sheet describes drain triac error sensing. The triac switches the pump on; sensing is the control checking that switch's result. A mismatch is stored as E24.
Read the supporting manualThe sheet sends all three to the same drain test. The pump circuit is the common thread, though E21 is about how fast water leaves and E24 is about what the board senses.
Read the supporting manualAfter the hose check, the sheet starts the washer and looks for 120 VAC at the drain pump. If the reading is zero it checks wiring, then the board. If voltage is present it removes the pump and looks for blockage.
Read the supporting manualIf the tub drains each time, a load is reasonable, but a pump that cannot be confirmed may stop mid-cycle with a full tub. Plan the visit rather than waiting.
Read the supporting manualManufacturer document
Electrolux (technician sheet; retailer-hosted copy)
A11200302 (1803); 2018, 300/400/500/600 series (EFLS527UTT and EFLS627UTT copies are byte-identical) / p.1 (Washer Error Codes)
Row 24 of the 2018 front-load washer sheet (the washer sheet). It sits beside E21 and E23 in test 3; this sheet marks it as a stored-only code.
The meaning differs: E23 is the triac error and E24 is its sensing. Owners see the same result, a drain concern, and the sheet sends both to test 3.
The test does include a pump blockage check, but only when the pump is receiving voltage. The code alone does not name a blockage.
No. For E24 the sheet's display column says no, so you are more likely to notice a drain that stalls than to see a message.
Note the model, whether E21 appeared as well, and whether the washer stops with water in the tub.
Codes, symptoms, parts and service
E23 on an Electrolux front-load washer is a drain triac error on the technician sheet. The display does not show E23. Owners can check the drain hose, but the sheet's next steps are electrical, so book a technician if the washer will not drain.
A washer that will not spin is most often reacting to an unbalanced or heavy load, a machine that is out of level, or a door that is not locked. Electrolux's sheet ties the motor-speed codes E55 and E59 to the motor, belt, tub bearings and motor control board.
The drain pump clears water from the tub. Electrolux’s washer sheet ties E21, E23 and E24 to it: water that pumps out too slowly, and errors in the board’s switching or sensing of the pump. The sheet points them all to one test.
Book a diagnostic for your model at the appliance.
Office details and the access information to pass on.