Start from the symptom
Electrolux washer not draining.
A washer that is slow to empty is most often fighting a kinked or poorly installed drain hose. Electrolux's E21 means water is not pumping out fast enough, and the sheet ties E21, E23 and E24 to the drain pump circuit.

Start with safe observations.
Power the appliance down and pull the plug before any owner check. Beware of standing water and sharp debris. Never touch a wet plug or electrical area, take off service panels, or step beyond your model’s owner guide.
- 1
Straighten the drain hose
Electrolux calls a kinked drain hose the most common cause of E21. Look along its whole run.
- 2
Check how the hose is installed
The E21 article asks that the drain hose be installed as the use and care manual shows. The slow-drain article, written about top-load washers, says the standpipe may be no higher than 96 inches and no narrower than 1 1/4 inches.
- 3
Leave air in the standpipe
If the hose is sealed in with tape, the seal should not be airtight, because the standpipe needs air to drain.
- 4
Look at detergent
The drainage article says too much laundry detergent can inhibit draining. Use the recommended amount and stay under the maximum fill lines.
- 5
Check the hoses at the faucets
Electrolux asks you to make sure the hot and cold inlet hoses are not reversed. It calls this a known installation issue for a recently installed or moved washer.
- 6
Pump suspicion
If you think the pump is clogged, Electrolux's drainage article points you to service. Electrolux describes a low hum while draining as the sound of the drain pump working.
Systems a technician may investigate.
The parts below tie in with this symptom. Seeing it does not prove any one of them has failed.
If the display adds a code.
Drain
E21 on an Electrolux front-load washer means the water is not pumping out fast enough. Check the drain hose for a kink first, then confirm the hot and cold lines and the hose installation. If it persists, book a technician.
Drain
E23 on an Electrolux front-load washer is a drain triac error on the technician sheet. The display does not show E23. Owners can check the drain hose, but the sheet's next steps are electrical, so book a technician if the washer will not drain.
Drain
E24 on an Electrolux front-load washer is the drain triac sensing row. The control cannot confirm the switching that runs the drain pump. It is not shown on the display, so check the drain hose and book a technician.
Read the related care guide.

Washer stopped, nothing on the display? Recall the code.
An Electrolux front-load washer shows only some codes. To read the last stored one, power on, wait at least 10 seconds, then hold temp and select for 3 seconds. The display shows the last error in memory. Hidden codes include E13, E23, E31 and E62, and they need a technician.

Detergent left in the drawer? Check the product, the packs and the water.
Electrolux's written sources name no single cause for a drawer that stays full. They list what interferes: a pack in the drawer, detergent above the max fill line, an unseated drawer, buildup, and water that never arrives. Work through these, then book a technician.
When observation becomes a service request.
Leave internal testing to a technician.
Book a visit if the hose is clear and installed correctly and the washer still leaves water in the tub or shows E21. The drain pump and its circuit, codes E21, E23 and E24, are where a technician starts.
Arrange a diagnosticSources and model boundaries.
These sources back the Electrolux washer not draining guidance. Use the manual for your own model.
- What should I do if my washer is draining slowly? (KB 1853030)
- Laundry front loading washer displaying Error Code E21 long pump out time. (KB 1820072)
- Laundry Washers Noises Guide (KB 1820062)
- Washer Tech Data Sheet, A11200302 (1803)
Follow the guide for your exact model. Consult how we research these pages.
What is E21 on an Electrolux washer?
It means the water is not pumping out fast enough, or takes too long to empty. The most common cause named by Electrolux is a kinked drain hose.
How high can the standpipe be?
Electrolux's drainage article says no taller than 96 inches and no narrower than 1 1/4 inches across.
Can the drain hose be taped into the standpipe?
Only if the seal is not airtight. The standpipe needs air for proper draining, so leave an air path and do not fit the hose too tightly.
Can too much detergent slow draining?
Yes, per Electrolux. Use the recommended amount and never fill a dispenser compartment above its maximum line.
Codes, symptoms, parts and service
Link the message to what to do next.
E21
E21 on an Electrolux front-load washer means the water is not pumping out fast enough. Check the drain hose for a kink first, then confirm the hot and cold lines and the hose installation. If it persists, book a technician.
Electrolux washer not spinning
A washer that will not spin is most often reacting to an unbalanced or heavy load, a machine that is out of level, or a door that is not locked. Electrolux's sheet ties the motor-speed codes E55 and E59 to the motor, belt, tub bearings and motor control board.
Washer drain pump
The drain pump clears water from the tub. Electrolux’s washer sheet ties E21, E23 and E24 to it: water that pumps out too slowly, and errors in the board’s switching or sensing of the pump. The sheet points them all to one test.
Washer repair
Book a diagnostic for your model at the appliance.
Find your metro
Office details and the access information to pass on.
