Electrolux washer HO SE / Water supply

Electrolux washer
error HO SE

Washer / display referenceHO SE

HO SE flashing on an Electrolux front-load washer means the hot and cold inlet hoses are reversed. Close both taps, press Cancel, and connect each hose to the correct inlet. If the washer was installed in the past 30 days, call the installer.

Also shown as HO SE

Last reviewed

Washer / display referenceHO SE
Meaning
HO SE flashing on an Electrolux front-load washer means the hot and cold inlet hoses are reversed. Close both taps, press Cancel, and connect each hose to the correct inlet. If the washer was installed in the past 30 days, call the installer.
Who handles it
Owner checks first, then a technician
Related codes
Source
Laundry front loading washer displaying Error Code HO SE reversed hose detection. (KB 1829275)

What Electrolux washer HO SE means.

What it means

HO SE flashing on an Electrolux front-load washer means the hot and cold inlet hoses are reversed. Close both taps, press Cancel, and connect each hose to the correct inlet. If the washer was installed in the past 30 days, call the installer.

What you can safely check

Electrolux says to shut off the water first.

When to call a technician

HO SE returns after the hoses are on the right inlets.

Your checklist, kept on this device

Safe checks, in order.

0 of 5 checks done
  1. Electrolux washer HO SE: Hand pointing at a red-handled shut-off valve on a tiled wall, with two braided hoses running to the red and blue inlets on the back of a washer
    Illustration. Follow your model’s instructions.
    Before you begin

    Turn off both water taps

    Electrolux says to shut off the water first. Do this before you touch any hose.

  2. Washers in a thoughtfully designed home
    Illustration. Follow your model’s instructions.
    Check 2

    Press Cancel

    The display shows HO, then SE, then the remaining cycle time for 60 seconds and repeats. Press Cancel to stop the cycle.

  3. A dark glass touch panel on a white front-load dryer, the display unlit
    Illustration. Follow your model’s instructions.
    Check 3

    Swap the hoses

    Attach each supply hose to the correct inlet connection: hot supply to the hot inlet, cold supply to the cold inlet.

  4. Technician in navy coveralls holding a tablet with a blank checklist, a washer in the background.
    Illustration. Follow your model’s instructions.
    Check 4

    Check for leaks

    Turn the taps on slowly and look at both ends of each hose for drips.

  5. A technician inspecting a front-load washer pump filter
    Illustration. Follow your model’s instructions.
    Check 5

    Book a visit

    If HO SE returns with the hoses correct, tell us the model and when the washer was installed.

Still showing HO SE?

Send us the model and the checks you have done, and open your request here.

Book a visit

Water into the washer.

Conceptual Washer sectionSupply valveInlet hoseTub inlet123
  1. 1Supply valve
  2. 2Inlet hose
  3. 3Tub inlet

A simplified drawing, since layouts differ between models. Pick an outlined part for its photo and the related check.

A little more context.

What does HO SE mean?

The washer has detected that the inlet hoses were installed backwards: hot supply on the cold inlet and cold supply on the hot inlet. It alerts you with HO SE on the display.

Read the supporting manual

What does the display do?

It shows HO, then SE, then the remaining cycle time (0 min) for about 60 seconds, then repeats until you press Cancel.

Read the supporting manual

Who should fix it?

You can swap the hoses with the taps off. Within 30 days of installation, Electrolux sends you to your installer. After that, book a visit with us.

Read the supporting manual

How is HO SE related to F9 and E11?

F9 is the sheet's hot valve warning for the same cause, and E11 is a slow fill that reversed hoses can also produce.

Read the supporting manual

The manual behind the message.

Manufacturer document

Laundry front loading washer displaying Error Code HO SE reversed hose detection. (KB 1829275)

Electrolux / Owner Center knowledge base (owner.electrolux.com)

Owner Center article, cached 10.11.2026 (no edition date printed) / article text

Owner Center article 1829275 for front-load washers. A displayed alert, not a numbered failure.

Here to help

Good questions.
Clear answers.

Talk to our team
Is HO SE dangerous?

No. It is a warning about water temperature, though a wet hose connection can spray, so close the taps first.

Will the washer run with HO SE?

It shows the alert and waits. Press Cancel and correct the hoses before you restart.

Why does the washer know the hoses are swapped?

Electrolux's article says it detects the condition. It does not explain how, so we do not either.

Do I need a plumber?

Usually not. Swapping two hoses is a hand-tight job with the taps closed.

Let’s take care of it.

Premium appliances deserve
careful service.