Start from the symptom
Electrolux washer not filling with water.
A front loader that fills slowly or not at all is usually short of water at the inlet: a closed faucet, reversed hoses, a kinked hose or a clogged inlet filter. Electrolux's E11 means the washer is not filling during the wash phase.

Start with safe observations.
Power the appliance down and pull the plug before any owner check. Beware of standing water and sharp debris. Never touch a wet plug or electrical area, take off service panels, or step beyond your model’s owner guide.
- 1
Turn both faucets fully on
Electrolux says the washer will not work properly without water. Confirm that the hot and cold supplies are open.
- 2
Hoses on the right inlets
The hot supply goes to the hot inlet and the cold to the cold. Reversed hoses cause E11 and HO SE. Electrolux calls this a known installation issue, so recheck a washer that was recently installed or moved.
- 3
Hoses snug, straight, unpinched
Hoses should be tight, with no kinks or pinches. Standard washer hoses are preferred; Electrolux says to replace flood-safe hoses with standard ones.
- 4
Check flow and filters
Turn off the water, disconnect the hoses and see whether water runs from the faucets. Then check the filters on the inlet connectors.
- 5
Water pressure
The supply guide gives 30 to 120 psi, with no more than 10 psi between hot and cold. Your local water department can tell you your pressure.
- 6
Waiting after E11
E11 can lock the washer for up to 6 minutes. Unplugging and replugging restarts that wait.
Systems a technician may investigate.
The parts below tie in with this symptom. Seeing it does not prove any one of them has failed.
If the display adds a code.
Water supply
E11 on an Electrolux front-load washer means the fill took too long, so water is not arriving fast enough. Check that both taps are open and the hot and cold hoses sit on the right inlets. The washer may stay locked for up to 6 minutes.
Water supply
F9 is a hot valve warning on Electrolux's 2018 washer sheet: the hot and cold water hoses are reversed. The sheet says to switch the hoses to reduce water-temperature problems. The display does not show F9. Close the taps before you swap them.
Read the related care guide.

Washer stopped, nothing on the display? Recall the code.
An Electrolux front-load washer shows only some codes. To read the last stored one, power on, wait at least 10 seconds, then hold temp and select for 3 seconds. The display shows the last error in memory. Hidden codes include E13, E23, E31 and E62, and they need a technician.

Detergent left in the drawer? Check the product, the packs and the water.
Electrolux's written sources name no single cause for a drawer that stays full. They list what interferes: a pack in the drawer, detergent above the max fill line, an unseated drawer, buildup, and water that never arrives. Work through these, then book a technician.
When observation becomes a service request.
Leave internal testing to a technician.
Book a visit if the faucets are open, the hoses are correct and clear, the filters are clean and the washer still fills slowly or throws E11. We can check the inlet valve and the pressure sensor.
Arrange a diagnosticSources and model boundaries.
These sources back the Electrolux washer not filling with water guidance. Use the manual for your own model.
- Laundry Water Supply Guide (KB 1820069)
- Laundry front loading washer displaying Error Code E11 long fill time. (KB 1820068)
- Laundry front loading washer displaying Error Code HO SE reversed hose detection. (KB 1829275)
- Washer Tech Data Sheet, A11200302 (1803)
Follow the guide for your exact model. Consult how we research these pages.
What does E11 mean on an Electrolux washer?
It means the washer is not filling during the wash phase. Electrolux lists reversed hot and cold hoses and water supply problems as the first things to check.
How long does E11 lock the washer?
Up to 6 minutes. Electrolux notes that if you unplug the washer and plug it back in, the six-minute lock starts again.
What water pressure does the washer need?
Between 30 and 120 psi, with no more than 10 psi difference between hot and cold. Your water department can tell you what your home gets.
What is HO SE?
It is the reversed hose alert. Turn off the water, press cancel and connect each supply hose to its matching inlet. The display shows HO, then SE, in a loop.
Codes, symptoms, parts and service
Link the message to what to do next.
E11
E11 on an Electrolux front-load washer means the fill took too long, so water is not arriving fast enough. Check that both taps are open and the hot and cold hoses sit on the right inlets. The washer may stay locked for up to 6 minutes.
Electrolux washer not spinning
A washer that will not spin is most often reacting to an unbalanced or heavy load, a machine that is out of level, or a door that is not locked. Electrolux's sheet ties the motor-speed codes E55 and E59 to the motor, belt, tub bearings and motor control board.
Washer pressure sensor
The pressure sensor tells the washer how high the water stands in the tub. Electrolux’s washer sheet ties it to E13, E31, E32 and E35. E35 means the sensor reports an overfill; E31 and E32 point at the sensor’s own reading or calibration.
Washer repair
Book a diagnostic for your model at the appliance.
Find your metro
Office details and the access information to pass on.
