What it means
EF2 is how owners write F2, the washer sheet's too much soap or wrong detergent type code. No Electrolux document prints it with an E. Use less detergent, make sure it is high efficiency, and run a rinse. The display shows it.
Electrolux washer EF2 / Suds
EF2 is how owners write F2, the washer sheet's too much soap or wrong detergent type code. No Electrolux document prints it with an E. Use less detergent, make sure it is high efficiency, and run a rinse. The display shows it.
Also shown as EF2
EF2 is how owners write F2, the washer sheet's too much soap or wrong detergent type code. No Electrolux document prints it with an E. Use less detergent, make sure it is high efficiency, and run a rinse. The display shows it.
The sheet's advice for F2 is to reduce the detergent.
EF2 returns with a measured amount of HE detergent.
Your checklist, kept on this device

The sheet's advice for F2 is to reduce the detergent. Use the amount on the pack for a front-load washer, or less for a small load.

Use a high-efficiency (HE) detergent. Standard detergent makes more suds than a front-load drum can handle.

Make sure no compartment is filled past its maximum line.

Start a rinse or an empty quick wash to clear leftover suds, then see whether the code returns.
If EF2 appears with a small amount of HE detergent, tell us the detergent and the load size.
Send us the model and the checks you have done, and open your request here.
Book a visitA simplified drawing, since layouts differ between models. Pick an outlined part for its photo and the related check.
Yes in practice. The technician sheet prints F2; owners often type EF2. We have no Electrolux page that prints the E form, so this page follows the sheet's F2 row.
Read the supporting manualToo much soap or the wrong type of soap. It is one of the few washer codes the sheet shows on the display, and its advice is to reduce detergent or change to high efficiency.
Read the supporting manualSU dS is the suds-protection message from the Owner Center article, where the washer adds rinses until the suds clear. Both come from too much suds.
Read the supporting manualUsually not. It is a laundry-habit code first, and a visit is only for a code that returns on a correct dose of HE detergent.
Read the supporting manualManufacturer document
Electrolux (technician sheet; retailer-hosted copy)
A11200302 (1803); 2018, 300/400/500/600 series (EFLS527UTT and EFLS627UTT copies are byte-identical) / p.2 (Washer Error Codes)
The sheet the washer sheet prints F2; owners write EF2. Displayed code with an owner-side cause.
Follow the amount on the detergent pack for a front-load washer and do not fill any dispenser compartment past its line.
If the washer runs extra rinses to clear suds, each can add roughly 5 minutes, as the Owner Center says for SU dS.
The sheet names only detergent amount and type, so we do not say. Keep any additive within its marked line.
Yes. The sheet marks it as shown, which makes it one of the few washer codes you can read directly.
Codes, symptoms, parts and service
SU dS means the washer detected too many suds and will run extra rinses until they clear, about 5 minutes each. Use high-efficiency detergent, use less of it, and run an empty quick wash to clean the unit. Press Cancel to clear the alert.
A washer that will not spin is most often reacting to an unbalanced or heavy load, a machine that is out of level, or a door that is not locked. Electrolux's sheet ties the motor-speed codes E55 and E59 to the motor, belt, tub bearings and motor control board.
Book a diagnostic for your model at the appliance.
Office details and the access information to pass on.