Start from the symptom
Electrolux washer shaking or banging.
Violent shaking is usually a load that is off balance or a washer that is not resting level on a solid floor. Electrolux's noise guide adds shipping bolts, stacking hardware and a drain hose that slaps the cabinet.

Start with safe observations.
Power the appliance down and pull the plug before any owner check. Beware of standing water and sharp debris. Never touch a wet plug or electrical area, take off service panels, or step beyond your model’s owner guide.
- 1
Rebalance the load
Power the washer down, let the door or lid release, then spread the laundry out. With a small load, a couple of similar items help before you restart.
- 2
Make it level
Use a level across the cabinet in both directions and check every leg bears on the floor. Turn the legs a little to adjust, then tighten the lock nuts. Electrolux limits leg extension to 1/2 inch below the cabinet.
- 3
Floor and shipping materials
Floors should be level and solid. Electrolux does not recommend carpet, loose plywood or unstable surfaces. On a new washer, look for shipping bolts and foam underneath.
- 4
Stacked units
If the washer and dryer are stacked, check the stacking kit, that the feet are fully screwed in and that every bracket is tight.
- 5
Tie down the drain hose
Knocking can be an unsecured drain hose hitting the back of the unit. Electrolux suggests securing it with zip ties.
- 6
Know the normal sounds
A heavy load may thump as the spin builds; high-pitched spinning, gurgling when it drains and clicks from the door lock and water valves are all described as ordinary.
Systems a technician may investigate.
The linked parts are the ones Electrolux’s technician sheets name for this appliance. We confirm each against your model number once the diagnostic is done, and you approve any replacement first.

Washer pressure sensor
The pressure sensor tells the washer how high the water stands in the tub. Electrolux’s washer sheet ties it to E13, E31, E32 and E35. E35 means the sensor reports an overfill; E31 and E32 point at the sensor’s own reading or calibration.

Washer door lock
The door lock keeps the washer closed during a cycle and tells the control the door is shut. Electrolux’s sheet lists five door codes. E41 means the board thinks the door switch is open; E42 and E43 are about the lock itself; E44 and E45 about sensing.

Washer drain pump
The drain pump clears water from the tub. Electrolux’s washer sheet ties E21, E23 and E24 to it: water that pumps out too slowly, and errors in the board’s switching or sensing of the pump. The sheet points them all to one test.
Read the related care guide.

Washer stopped, nothing on the display? Recall the code.
An Electrolux front-load washer shows only some codes. To read the last stored one, power on, wait at least 10 seconds, then hold temp and select for 3 seconds. The display shows the last error in memory. Hidden codes include E13, E23, E31 and E62, and they need a technician.

Detergent left in the drawer? Check the product, the packs and the water.
Electrolux's written sources name no single cause for a drawer that stays full. They list what interferes: a pack in the drawer, detergent above the max fill line, an unseated drawer, buildup, and water that never arrives. Work through these, then book a technician.
When observation becomes a service request.
Leave internal testing to a technician.
If a small balanced load on a level floor still shakes the washer once the shipping bolts are out, book a visit. We can look at the tub bearings and the motor drive that the guide does not cover.
Arrange a diagnosticSources and model boundaries.
These sources back the Electrolux washer shaking or banging guidance. Use the manual for your own model.
- Laundry Washers Noises Guide (KB 1820062)
- Washer Tech Data Sheet, A11200302 (1803)
Follow the guide for your exact model. Consult how we research these pages.
Why does my washer bang during the spin?
Most often the load is bunched on one side or the washer is not level. Pause, redistribute the clothes and check the legs with a level.
How far can the leveling legs extend?
Electrolux caps it at 1/2 inch beneath the cabinet. Adjust them until the washer rests firmly, then tighten the lock nuts.
What does EF5 mean?
The sheet lists EF5 as load unbalanced. It is not a display code on most models, so you may just see shaking or an extended spin.
Can the drain hose make knocking sounds?
Yes. Electrolux says an unsecured drain hose can hit the back of the unit. Secure it with zip ties so it cannot slap or rub.
Codes, symptoms, parts and service
Link the message to what to do next.
EF5
EF5 is how owners write F5, the sheet's load unbalanced code. No Electrolux document prints it with an E. Open the door, redistribute the clothes and restart. The display does not show it; a wet bundle or one heavy item is the usual cause.
Electrolux washer not spinning
A washer that will not spin is most often reacting to an unbalanced or heavy load, a machine that is out of level, or a door that is not locked. Electrolux's sheet ties the motor-speed codes E55 and E59 to the motor, belt, tub bearings and motor control board.
Washer repair
Book a diagnostic for your model at the appliance.
Find your metro
Office details and the access information to pass on.