Start from the symptom
Electrolux washer leaking water.
Work out the source of the water first. Electrolux sorts front-load leaks into four spots: the inlet hoses, the drain hose, the door seal and the dispenser drawer. Each has its own quick check, and a leaking tub or sensor shows as E13.

Start with safe observations.
Power the appliance down and pull the plug before any owner check. Beware of standing water and sharp debris. Never touch a wet plug or electrical area, take off service panels, or step beyond your model’s owner guide.
- 1
Stop and dry the area
Turn off the water supply and wipe up the floor so you can see the next drip.
- 2
Inlet hoses
Inspect hoses for kinks and pinholes, and every connection too. Remove a leaking connection, inspect the O-ring and replace it if it is damaged or missing. Hand tighten, then add about half a turn with a wrench.
- 3
Cracked connectors
Inspect the blue and red connectors on the washer. Cracks are normally caused by over-tightening, and Electrolux says to schedule service if you find one.
- 4
Drain hose
The drain hose should be secured to the drainpipe with a tie or bracket. Run a gallon of water into the drainpipe: if it backs up, the home drain is clogged and you need a plumber.
- 5
Door seal and glass
Clean the rubber seal and the glass to remove hair, dirt, lint and clothing. If the seal is clean and it still leaks, schedule service.
- 6
Dispenser drawer
The drawer must be on its rails and fully closed, with compartments seated, the washer level and the water pressure not too high. Buildup in the drawer can leak.
- 7
E13
The sheet lists E13 as a water leak in the tub or the pressure sensor, and it is not shown on the display.
Systems a technician may investigate.
The parts below tie in with this symptom. Seeing it does not prove any one of them has failed.
Read the related care guide.

Washer stopped, nothing on the display? Recall the code.
An Electrolux front-load washer shows only some codes. To read the last stored one, power on, wait at least 10 seconds, then hold temp and select for 3 seconds. The display shows the last error in memory. Hidden codes include E13, E23, E31 and E62, and they need a technician.

Detergent left in the drawer? Check the product, the packs and the water.
Electrolux's written sources name no single cause for a drawer that stays full. They list what interferes: a pack in the drawer, detergent above the max fill line, an unseated drawer, buildup, and water that never arrives. Work through these, then book a technician.
When observation becomes a service request.
Leave internal testing to a technician.
Book a visit if water still escapes after the hoses, drain, seal and drawer check out, or if you find a cracked connector, a damaged drain hose or water under the tub. Switch the washer off at the outlet and keep the faucets closed until we arrive.
Arrange a diagnosticSources and model boundaries.
These sources back the Electrolux washer leaking water guidance. Use the manual for your own model.
- Laundry front loading washer is leaking water. (KB 1831358)
- Washer Tech Data Sheet, A11200302 (1803)
Follow the guide for your exact model. Consult how we research these pages.
Where do Electrolux front loaders usually leak?
Electrolux names four places: inlet hoses and their connections, the drain hose, the door seal and the dispenser drawer. Locating the drip tells you which check applies.
How tight should hose connections be?
Hand tight first, then a half turn more with a wrench after you have inspected the O-ring. Over-tightening cracks the blue and red connectors.
How can I tell whether my drain is clogged?
Send a gallon of water down the drainpipe. If it rises back up, the home drain is clogged and a plumber should clear it.
What is E13?
The sheet describes E13 as a water leak in the tub or in the pressure sensor. It is not shown on the display, so it is read from stored errors.
Codes, symptoms, parts and service
Link the message to what to do next.
E13
E13 on an Electrolux front-load washer means water is leaking in the tub or the pressure-sensor line. The sheet does not show it on the display. Shut the taps, unplug the washer if water is escaping, and book a technician.
Electrolux washer not spinning
A washer that will not spin is most often reacting to an unbalanced or heavy load, a machine that is out of level, or a door that is not locked. Electrolux's sheet ties the motor-speed codes E55 and E59 to the motor, belt, tub bearings and motor control board.
Washer pressure sensor
The pressure sensor tells the washer how high the water stands in the tub. Electrolux’s washer sheet ties it to E13, E31, E32 and E35. E35 means the sensor reports an overfill; E31 and E32 point at the sensor’s own reading or calibration.
Washer repair
Book a diagnostic for your model at the appliance.
Find your metro
Office details and the access information to pass on.
