What it means
E84 is a recirculation pump triac sensing failure that stops the cycle, on Electrolux's 2018 washer sheet (select models). The display does not show E84. The sheet's next step is to replace the main board, so book a technician.
Electrolux washer E84 / Pump
E84 is a recirculation pump triac sensing failure that stops the cycle, on Electrolux's 2018 washer sheet (select models). The display does not show E84. The sheet's next step is to replace the main board, so book a technician.
Also shown as E84
E84 is a recirculation pump triac sensing failure that stops the cycle, on Electrolux's 2018 washer sheet (select models). The display does not show E84. The sheet's next step is to replace the main board, so book a technician.
The recirculation pump belongs to models with a recirculating wash system.
E84 stops cycles twice running.
Your checklist, kept on this device

The recirculation pump belongs to models with a recirculating wash system. If yours lacks one, tell us the model.

E84 halts the cycle. The point where it stopped helps the technician.

Unplug the washer and use the drain method in the Use and Care guide if the tub is full.

Wait ten seconds after power on, hold Temp and Select for three seconds.

Unlike most rows, the sheet's instruction here is simply replace main board.
Send us the model and the checks you have done, and open your request here.
Book a visit
A simplified drawing, since layouts differ between models. Pick an outlined part for its photo and the related check.

Component reference
The main control board runs an Electrolux front-load washer and talks to the user interface and the motor control.
Read the definitionThe control could not verify the switching of the recirculation pump. The sheet reads recirculation pump triac sensing failure which stops the cycle (on select models).
Read the supporting manualIts next step for E84 is replace main board, with no pump or wiring test. That makes sense for a sensing circuit that lives on the board itself.
Read the supporting manualE85 is the pump triac alarm. Its test checks the pump wiring, then the pump, then the board. E84 skips to the board.
Read the supporting manualIt is a safety stop. Plan a visit rather than forcing restarts.
Read the supporting manualManufacturer document
Electrolux (technician sheet; retailer-hosted copy)
A11200302 (1803); 2018, 300/400/500/600 series (EFLS527UTT and EFLS627UTT copies are byte-identical) / p.2 (Washer Error Codes)
Row 84 of the washer sheet: select models with a recirculation pump; next step replace main board.
It moves wash water from the bottom of the tub back over the load. It is separate from the drain pump, so a drain problem is a different code.
It might clear the message for a while, but a sensing circuit that fails once tends to fail again, and the sheet's answer is a new board.
No. The sheet lists it as not shown, so you will mostly see a cycle that stops early.
It should, since the drain pump is a separate circuit. If water stays in the tub, check E21 as well.
Codes, symptoms, parts and service
E85 is a recirculation pump triac alarm that stops the cycle, on Electrolux's 2018 washer sheet, for select models. The display does not show E85. Book a technician; the sheet checks the pump wiring, the pump and then the board.
A washer that will not spin is most often reacting to an unbalanced or heavy load, a machine that is out of level, or a door that is not locked. Electrolux's sheet ties the motor-speed codes E55 and E59 to the motor, belt, tub bearings and motor control board.
The main control board runs an Electrolux front-load washer and talks to the user interface and the motor control. Electrolux's washer sheet names it for E91 to E94, E97 and E98, and for E84 where it says to replace the main board. The first step is one restart.
Book a diagnostic for your model at the appliance.
Office details and the access information to pass on.