What it means
E62 on the 2018 Electrolux washer sheet means the wash temperature went too high. The display does not show E62. Stop the cycle, unplug the washer and book a technician; the sheet sends it to the temperature sensor and heater tests.
Electrolux washer E62 / Heating
E62 on the 2018 Electrolux washer sheet means the wash temperature went too high. The display does not show E62. Stop the cycle, unplug the washer and book a technician; the sheet sends it to the temperature sensor and heater tests.
Also shown as E62
E62 on the 2018 Electrolux washer sheet means the wash temperature went too high. The display does not show E62. Stop the cycle, unplug the washer and book a technician; the sheet sends it to the temperature sensor and heater tests.
Do not open the door while the drum is hot.
E62 returns or the water is hotter than the cycle should make it.
Your checklist, kept on this device

Do not open the door if the wash water feels hot to the touch. Cancel the cycle, let the washer cool, then cut the power.

Confirm that you selected a heated cycle on purpose. A sanitizing or hot cycle runs warmer than a cold one.

If the hot and cold hoses are reversed, the washer may take hotter water than expected, so look at the connections.

After ten seconds with the power on, hold Temp and Select down together for three seconds, and read E62.

Tests 13 and 14 cover the tub temperature sensor and the heating element, both inside the cabinet.
Send us the model and the checks you have done, and open your request here.
Book a visit
A simplified drawing, since layouts differ between models. Pick an outlined part for its photo and the related check.

Component reference
On select Electrolux front-load washers, an internal tub heater warms the wash water, and a temperature sensor (NTC) watches it.
Read the definitionThe control measured a wash temperature above its limit. The sheet lists it as wash temperature too high and does not show it on the display.
Read the supporting manualTest 13 measures the water NTC sensor, around 4.8K ohms, and test 14 measures the heating element near 14 ohms and its insulation to ground.
Read the supporting manualPossibly, though the sheet doesn't list hoses for E62. Swapped hoses are a known installation issue in other Electrolux articles, so check them.
Read the supporting manualOverheated water can scald and stress seals. Treat it seriously.
Read the supporting manualManufacturer document
Electrolux (technician sheet; retailer-hosted copy)
A11200302 (1803); 2018, 300/400/500/600 series (EFLS527UTT and EFLS627UTT copies are byte-identical) / p.2 (Washer Error Codes)
Row 62 of the 2018 washer sheet, on models with a heater. Tests 13 and 14.
No. E74 means the wash temperature does not rise. E62 is the opposite problem, a wash that gets too hot.
No. For E62 the sheet's display column says no, so recall the stored error to confirm it.
Yes. It is the first thing test 13 checks, with a reading near 4.8K ohms expected.
Only if the washer finishes a cold cycle with no code. Do not run hot or sanitizing cycles until it has been checked.
Codes, symptoms, parts and service
E74 on the 2018 Electrolux washer sheet means the wash temperature does not increase. The display does not show E74. Cold cycles may still run; a technician checks the water temperature sensor and the heater.
A washer that will not spin is most often reacting to an unbalanced or heavy load, a machine that is out of level, or a door that is not locked. Electrolux's sheet ties the motor-speed codes E55 and E59 to the motor, belt, tub bearings and motor control board.
On select Electrolux front-load washers, an internal tub heater warms the wash water, and a temperature sensor (NTC) watches it. Electrolux's washer sheet names the heater for E66, E68 and E69, and the sensor for E71. Cold cycles may still run; the heater tests are for a technician.
Book a diagnostic for your model at the appliance.
Office details and the access information to pass on.