What it means
E66 is a heater relay problem on Electrolux's 2018 washer sheet, listed for select models that have an internal heater. The display does not show E66. Unplug the washer and book a technician; the sheet sends E66 to its heater test.
Electrolux washer E66 / Heating
E66 is a heater relay problem on Electrolux's 2018 washer sheet, listed for select models that have an internal heater. The display does not show E66. Unplug the washer and book a technician; the sheet sends E66 to its heater test.
Also shown as E66
E66 is a heater relay problem on Electrolux's 2018 washer sheet, listed for select models that have an internal heater. The display does not show E66. Unplug the washer and book a technician; the sheet sends E66 to its heater test.
The sheet marks E66 as select models only, so look at the model number before you worry.
E66 is stored again, or hot cycles behave oddly after a restart.
Your checklist, kept on this device

The sheet marks E66 as select models only, so look at the model number before you worry. Many washers in this range heat only with the hot water from the house.

Note whether the water warms up when it should, or warms when you chose cold. A relay that sticks either way gives a clue.

The relay switches the heater with line voltage on the main board. Cut the power at the plug and leave the panels on.

Press Power, give it ten seconds and hold Temp and Select for three seconds. If E66 is what the washer stored, it tells the visit where to start.

The heater test measures the element, then its insulation to ground, then the wiring, and the main board comes last.
Send us the model and the checks you have done, and open your request here.
Book a visit
A simplified drawing, since layouts differ between models. Pick an outlined part for its photo and the related check.

Component reference
On select Electrolux front-load washers, an internal tub heater warms the wash water, and a temperature sensor (NTC) watches it.
Read the definitionThe relay that switches the washer's heater is not behaving the way the control expects. The sheet lists it as heater relay problem (on select models) and does not show it to the owner.
Read the supporting manualTest 14 measures the element at about 14 ohms, checks that neither heater terminal leaks to ground, inspects the wiring, and replaces the main board if the rest is sound.
Read the supporting manualE6A is the control failing to read the relay's state, while E66 is the relay problem itself. Both share test 14, so the visit is the same.
Read the supporting manualNot until a technician has looked. A relay that sticks closed could keep heating the water longer than the cycle intends, so choose cold washes meanwhile.
Read the supporting manualManufacturer document
Electrolux (technician sheet; retailer-hosted copy)
A11200302 (1803); 2018, 300/400/500/600 series (EFLS527UTT and EFLS627UTT copies are byte-identical) / p.2 (Washer Error Codes)
Row 66 of the washer sheet, flagged for select models with a heater. It shares test 14 with E62, E68, E69, E6A and E74.
Only washers with an internal tub heater have a heater relay to report on. Your model label tells you which group you are in.
It might finish a cold cycle, but the heating side is in doubt, so treat hot and sanitizing cycles as unavailable until it is checked.
The relay carries line voltage, so panels stay on. The ground-leakage row is E68, which is the one that points at a shock hazard.
The model number, which cycle was running when the washer stopped, and whether the water felt warm.
Codes, symptoms, parts and service
E6A is a heater relay sensing problem on the 2018 Electrolux washer sheet (select models): the control cannot read what the heater relay is doing. The display does not show E6A. Choose cold cycles and book a technician for test 14.
A washer that will not spin is most often reacting to an unbalanced or heavy load, a machine that is out of level, or a door that is not locked. Electrolux's sheet ties the motor-speed codes E55 and E59 to the motor, belt, tub bearings and motor control board.
On select Electrolux front-load washers, an internal tub heater warms the wash water, and a temperature sensor (NTC) watches it. Electrolux's washer sheet names the heater for E66, E68 and E69, and the sensor for E71. Cold cycles may still run; the heater tests are for a technician.
Book a diagnostic for your model at the appliance.
Office details and the access information to pass on.