What it means
E6A is a heater relay sensing problem on the 2018 Electrolux washer sheet (select models): the control cannot read what the heater relay is doing. The display does not show E6A. Choose cold cycles and book a technician for test 14.
Electrolux washer E6A / Heating
E6A is a heater relay sensing problem on the 2018 Electrolux washer sheet (select models): the control cannot read what the heater relay is doing. The display does not show E6A. Choose cold cycles and book a technician for test 14.
Also shown as E6A
E6A is a heater relay sensing problem on the 2018 Electrolux washer sheet (select models): the control cannot read what the heater relay is doing. The display does not show E6A. Choose cold cycles and book a technician for test 14.
Until the control can read the relay, avoid long hot or sanitizing cycles.
E6A is stored again after a restart.
Your checklist, kept on this device

Until the control can read the relay, avoid long hot or sanitizing cycles.

Tell us whether hot cycles warm up and whether they overshoot.

The sensing circuit sits on the main control board. Leave the cover on.

After ten seconds on, hold Temp and Select together for three seconds.

Test 14 measures the element, checks ground leakage, inspects the wiring and, if all is good, replaces the main board.
Send us the model and the checks you have done, and open your request here.
Book a visit
A simplified drawing, since layouts differ between models. Pick an outlined part for its photo and the related check.

Component reference
On select Electrolux front-load washers, an internal tub heater warms the wash water, and a temperature sensor (NTC) watches it.
Read the definitionThe main board cannot confirm the position of the heater relay. The sheet reads heater relay sensing problem, for select models, and does not show it on the display.
Read the supporting manualE66 is the relay misbehaving; E6A is the control's sensing of it failing. A technician treats both under test 14.
Read the supporting manualThe sheet measures the element at about 14 ohms, checks for ground leakage, checks wiring, and replaces the main control board last.
Read the supporting manualA cold cycle that completes is acceptable. Do not leave hot cycles unattended.
Read the supporting manualManufacturer document
Electrolux (technician sheet; retailer-hosted copy)
A11200302 (1803); 2018, 300/400/500/600 series (EFLS527UTT and EFLS627UTT copies are byte-identical) / p.2 (Washer Error Codes)
Row 6A of the washer sheet: select models with a heater. Test 14.
Not by itself. It means the control cannot verify the relay.
Only washers with an internal heater have a relay to sense.
No. For E6A the sheet's display column says no, so you confirm it by recalling the stored error.
The model number, the cycle you ran and whether the water got warm.
Codes, symptoms, parts and service
E66 is a heater relay problem on Electrolux's 2018 washer sheet, listed for select models that have an internal heater. The display does not show E66. Unplug the washer and book a technician; the sheet sends E66 to its heater test.
A washer that will not spin is most often reacting to an unbalanced or heavy load, a machine that is out of level, or a door that is not locked. Electrolux's sheet ties the motor-speed codes E55 and E59 to the motor, belt, tub bearings and motor control board.
On select Electrolux front-load washers, an internal tub heater warms the wash water, and a temperature sensor (NTC) watches it. Electrolux's washer sheet names the heater for E66, E68 and E69, and the sensor for E71. Cold cycles may still run; the heater tests are for a technician.
Book a diagnostic for your model at the appliance.
Office details and the access information to pass on.