Inside the appliance
Washer heater and water temperature sensor. In plain English.
On select Electrolux front-load washers, an internal tub heater warms the wash water, and a temperature sensor (NTC) watches it. Electrolux's washer sheet names the heater for E66, E68 and E69, and the sensor for E71. Cold cycles may still run; the heater tests are for a technician.

Where it fits.
Washer heater and water temperature sensor in the appliance
Inside the washer at the tub; the sheet refers to the tub heater and the drum water NTC but does not locate them further.
The image shows the type of component only. It does not select a replacement that fits your model.
What is different once this system needs attention.
Washer heater and water temperature sensor concerns may show up with a drop in performance or a code that keeps returning. Testing comes first before anyone decides the component has failed.

Electrolux washer not spinning
A washer that will not spin is most often reacting to an unbalanced or heavy load, a machine that is out of level, or a door that is not locked. Electrolux's sheet ties the motor-speed codes E55 and E59 to the motor, belt, tub bearings and motor control board.

Electrolux washer detergent dispenser problems
Dispenser trouble on an Electrolux front loader usually comes from the wrong detergent, too much of it, a drawer that is not seated or buildup in the compartments. Detergent packs belong in the drum, not the drawer.
Owner care, within the model instructions.
Power the appliance down and pull the plug before any owner check. Beware of standing water and sharp debris. Never touch a wet plug or electrical area, take off service panels, or step beyond your model’s owner guide.
- 1
Check that you have the heater
The sheet marks E66, E68, E69, E6A and E71 as select models. Look at your model number.
- 2
Feel the water on a hot cycle
An open heater (E69) leaves the water at supply temperature. If a hot cycle never warms, that fits the code.
- 3
Use cold cycles meanwhile
If a cold wash finishes with no code, that is acceptable until the visit.
- 4
Unplug on E68
E68 is current leaking to ground from the heater or its wiring. Unplug the washer and leave it off.
- 5
Stay out of the tub area
The heater carries line voltage. Leave it to a technician.
Cleaning or replacement?
Leave internal testing to a technician.
E66, E68, E69, E6A or E71 appears.
Hot cycles never warm up.
The breaker trips as the washer heats.
Arrange a diagnosticSources and model boundaries.
These sources back the Washer heater and water temperature sensor guidance. Use the manual for your own model.
- Washer Tech Data Sheet, A11200302 (1803)
Follow the guide for your exact model. Consult how we research these pages.
Does my Electrolux washer have a heater?
Only select models. The sheet marks the heater codes E66, E68, E69 and E6A as on select models. Check your model number.
What does E69 mean?
The heater is open, a broken circuit. Cold cycles may still run, but hot cycles will not heat. Book a technician.
What does E71 mean?
A drum water NTC failure, the temperature sensor for the tub heater. The sheet checks the NTC resistance, then replaces it.
Is E68 dangerous?
It is current leakage to ground from the heater or its wiring. Unplug the washer, leave it off and book a technician.
Can I run cold cycles?
Often yes. The sheet's heater codes concern heating. Stop if a code returns on cold cycles and book a visit.
Codes, symptoms, parts and service
Link the message to what to do next.
E66
E66 is a heater relay problem on Electrolux's 2018 washer sheet, listed for select models that have an internal heater. The display does not show E66. Unplug the washer and book a technician; the sheet sends E66 to its heater test.
Electrolux washer not spinning
A washer that will not spin is most often reacting to an unbalanced or heavy load, a machine that is out of level, or a door that is not locked. Electrolux's sheet ties the motor-speed codes E55 and E59 to the motor, belt, tub bearings and motor control board.
Washer repair
Book a diagnostic for your model at the appliance.
Find your metro
Office details and the access information to pass on.

