Electrolux washer E69 / Heating

Electrolux washer
error E69

Washer / display reference

E69 means the washer heater is open, a broken circuit, on Electrolux's 2018 washer sheet (select models). The display does not show E69. Cold cycles may still run, but hot cycles will not heat, so book a technician for the heater test.

Also shown as E69

Last reviewed

Washer / display reference
Meaning
E69 means the washer heater is open, a broken circuit, on Electrolux's 2018 washer sheet (select models). The display does not show E69. Cold cycles may still run, but hot cycles will not heat, so book a technician for the heater test.
Who handles it
Technician
Related codes
Source
Washer Tech Data Sheet, A11200302 (1803)

What Electrolux washer E69 means.

What it means

E69 means the washer heater is open, a broken circuit, on Electrolux's 2018 washer sheet (select models). The display does not show E69. Cold cycles may still run, but hot cycles will not heat, so book a technician for the heater test.

What you can safely check

An open heater leaves the water at supply temperature.

When to call a technician

Hot cycles never warm or E69 is stored again.

Your checklist, kept on this device

Safe checks, in order.

0 of 5 checks done
  1. Electrolux washer E69: Underside of a washer tub with the heating element pulled out, mineral scale on the metal, a screwdriver and the unplugged cord on the floor
    Illustration. Follow your model’s instructions.
    Before you begin

    Feel the water on a hot cycle

    An open heater leaves the water at supply temperature. If a hot cycle never warms, that fits the code.

  2. Washers in a thoughtfully designed home
    Illustration. Follow your model’s instructions.
    Check 2

    Use cold cycles meanwhile

    The circuit being open means no current flows, which is the safe direction. If the washer finishes a cold wash with no code, that is acceptable until the visit.

  3. A dark glass touch panel on a white front-load dryer, the display unlit
    Illustration. Follow your model’s instructions.
    Check 3

    Stay out of the tub area

    The element sits at the bottom of the tub and carries line voltage. Leave it to a technician.

  4. Technician in navy coveralls holding a tablet with a blank checklist, a washer in the background.
    Illustration. Follow your model’s instructions.
    Check 4

    Recall the stored code

    Wait ten seconds after switching on, then hold Temp and Select three seconds.

  5. A technician inspecting a front-load washer pump filter
    Illustration. Follow your model’s instructions.
    Check 5

    Book a visit

    Test 14 measures the element, which should be about 14 ohms; an open one reads far higher.

Still showing E69?

Send us the model and the checks you have done, and open your request here.

Book a visit

Water heating and its sensor.

Conceptual Washer sectionHeaterTemperature sensorControl123
  1. 2Temperature sensor

A simplified drawing, since layouts differ between models. Pick an outlined part for its photo and the related check.

Parts behind the message.

Front-load washer with the glass door open, showing the perforated stainless drum and a small pool of water at the bottom

Component reference

Washer heater and water temperature sensor

On select Electrolux front-load washers, an internal tub heater warms the wash water, and a temperature sensor (NTC) watches it.

Read the definition

A little more context.

What does E69 mean?

The path through the heater is broken. The sheet's wording is simply heater open, and it applies to select models with an internal heater.

Read the supporting manual

How is an open heater confirmed?

Test 14 checks the element's resistance against the 14-ohm figure. A wrong reading means a new element; a right one moves the technician on to ground checks, wiring and the main board.

Read the supporting manual

Does E69 explain a cold wash?

It can. If the heater cannot conduct, cycles that call for heat will not get it, and E74 (wash temperature does not increase) may follow.

Read the supporting manual

Is E69 dangerous?

An open circuit by itself is not an electrical hazard, but a washer that cannot heat should be checked before you rely on sanitizing cycles.

Read the supporting manual

The manual behind the message.

Manufacturer document

Washer Tech Data Sheet, A11200302 (1803)

Electrolux (technician sheet; retailer-hosted copy)

A11200302 (1803); 2018, 300/400/500/600 series (EFLS527UTT and EFLS627UTT copies are byte-identical) / p.2 (Washer Error Codes)

Row 69 of the washer sheet: select models. Test 14, resistance of the element near 14 ohms.

Here to help

Good questions.
Clear answers.

Talk to our team
Will the washer clean in cold water?

It can, but detergents work well at the temperature they are rated for, so results may vary.

Is E69 the same as E74?

No. E69 says the heater circuit is broken. E74 is the result the control sees: the water does not warm.

Is the element or the wiring open?

The sheet's test finds out. It measures the element first.

Do all Electrolux washers have this heater?

No. The sheet lists E69 for select models only. Washers without an internal heater rely on the hot water from the house.

Let’s take care of it.

Premium appliances deserve
careful service.