What it means
E68 means current is leaking to ground from the heater or its wiring, per the 2018 Electrolux washer sheet, for select models. The display does not show E68. Unplug the washer, do not run it again, and book a technician.
Electrolux washer E68 / Heating
E68 means current is leaking to ground from the heater or its wiring, per the 2018 Electrolux washer sheet, for select models. The display does not show E68. Unplug the washer, do not run it again, and book a technician.
Also shown as E68
E68 means current is leaking to ground from the heater or its wiring, per the 2018 Electrolux washer sheet, for select models. The display does not show E68. Unplug the washer, do not run it again, and book a technician.
Leakage to ground is a shock hazard, and the sheet's own advice is to disconnect power before servicing.
Any tingle, tripped breaker or repeat of E68; the washer stays off.
Your checklist, kept on this device

Leakage to ground is a shock hazard, and the sheet's own advice is to disconnect power before servicing. Leave it off until it has been checked.

If the cabinet tingles when touched or the breaker or GFCI trips as the washer heats, tell us. Do not touch the washer to test.

A grounded three-prong outlet matters on any washer. Never remove the ground pin or use an adapter.

With the washer on, wait about ten seconds and press and hold Temp plus Select for three seconds to see E68 in memory.

Test 14 measures resistance from each heater terminal to ground with the leads off; it should read open.
Send us the model and the checks you have done, and open your request here.
Book a visit
A simplified drawing, since layouts differ between models. Pick an outlined part for its photo and the related check.

Component reference
On select Electrolux front-load washers, an internal tub heater warms the wash water, and a temperature sensor (NTC) watches it.
Read the definitionThe control detected current escaping toward ground from the heater or the wiring that feeds it. The sheet states current leakage to ground on heater or wiring, for select models.
Read the supporting manualIn test 14 the technician disconnects the heater terminals and checks each one against ground. Anything other than open means the element is replaced.
Read the supporting manualOther heater rows mean the water will not heat. E68 means electricity is going where it should not, so the washer should not run until it is repaired.
Read the supporting manualYes. E69 is an open circuit, no current at all. E68 is current where it should not be. Both are checked in test 14.
Read the supporting manualManufacturer document
Electrolux (technician sheet; retailer-hosted copy)
A11200302 (1803); 2018, 300/400/500/600 series (EFLS527UTT and EFLS627UTT copies are byte-identical) / p.2 (Washer Error Codes)
Row 68 of the washer sheet: select models with a heater. Test 14, ground-leakage step.
We would not. The leakage is on the heater side, but the washer shares wiring, so leave it unplugged until it is checked.
A GFCI outlet tripping when the washer heats is the kind of sign that belongs in your notes for the visit.
The sheet names no cause beyond the heater or its wiring.
No, so you may only see the washer stop. Recall the stored code to confirm.
Codes, symptoms, parts and service
E69 means the washer heater is open, a broken circuit, on Electrolux's 2018 washer sheet (select models). The display does not show E69. Cold cycles may still run, but hot cycles will not heat, so book a technician for the heater test.
A washer that will not spin is most often reacting to an unbalanced or heavy load, a machine that is out of level, or a door that is not locked. Electrolux's sheet ties the motor-speed codes E55 and E59 to the motor, belt, tub bearings and motor control board.
On select Electrolux front-load washers, an internal tub heater warms the wash water, and a temperature sensor (NTC) watches it. Electrolux's washer sheet names the heater for E66, E68 and E69, and the sensor for E71. Cold cycles may still run; the heater tests are for a technician.
Book a diagnostic for your model at the appliance.
Office details and the access information to pass on.