Electrolux washer E71 / Heating

Electrolux washer
error E71

Washer / display reference

E71 on the 2018 Electrolux washer sheet is a drum water NTC failure, the temperature sensor for the tub heater, on select models. The display does not show E71. Book a technician; the sheet checks the sensor's resistance, then its wiring.

Also shown as E71

Last reviewed

Washer / display reference
Meaning
E71 on the 2018 Electrolux washer sheet is a drum water NTC failure, the temperature sensor for the tub heater, on select models. The display does not show E71. Book a technician; the sheet checks the sensor's resistance, then its wiring.
Who handles it
Technician
Related codes
Source
Washer Tech Data Sheet, A11200302 (1803)

What Electrolux washer E71 means.

What it means

E71 on the 2018 Electrolux washer sheet is a drum water NTC failure, the temperature sensor for the tub heater, on select models. The display does not show E71. Book a technician; the sheet checks the sensor's resistance, then its wiring.

What you can safely check

The temperature sensor mainly matters when the heater is used.

When to call a technician

E71 is stored again or hot cycles misbehave.

Your checklist, kept on this device

Safe checks, in order.

0 of 5 checks done
  1. Electrolux washer E71: Underside of a washer tub with the heating element pulled out, mineral scale on the metal, a screwdriver and the unplugged cord on the floor
    Illustration. Follow your model’s instructions.
    Before you begin

    Try a cold cycle

    The temperature sensor mainly matters when the heater is used. A cold wash may still finish.

  2. Washers in a thoughtfully designed home
    Illustration. Follow your model’s instructions.
    Check 2

    Note any heating oddities

    Water that never warms, or a cycle that runs unusually long on hot, belongs in your notes.

  3. A dark glass touch panel on a white front-load dryer, the display unlit
    Illustration. Follow your model’s instructions.
    Check 3

    Leave the sensor connector

    It sits low on the tub with other wiring. Unplug the washer and leave it in place.

  4. Technician in navy coveralls holding a tablet with a blank checklist, a washer in the background.
    Illustration. Follow your model’s instructions.
    Check 4

    Read the stored code

    With the washer on, wait about ten seconds and press and hold Temp plus Select for three seconds.

  5. A technician inspecting a front-load washer pump filter
    Illustration. Follow your model’s instructions.
    Check 5

    Book a visit

    Test 13 measures the NTC, which should read around 4.8K ohms.

Still showing E71?

Send us the model and the checks you have done, and open your request here.

Book a visit

Water heating and its sensor.

Conceptual Washer sectionHeaterTemperature sensorControl123
  1. 2Temperature sensor

A simplified drawing, since layouts differ between models. Pick an outlined part for its photo and the related check.

Parts behind the message.

Front-load washer with the glass door open, showing the perforated stainless drum and a small pool of water at the bottom

Component reference

Washer heater and water temperature sensor

On select Electrolux front-load washers, an internal tub heater warms the wash water, and a temperature sensor (NTC) watches it.

Read the definition

A little more context.

What does E71 mean?

The control sees a failure from the water temperature sensor in the drum, an NTC, which feeds the tub heater control.

Read the supporting manual

How is it tested?

Test 13: measure the NTC's resistance. About 4.8K ohms is normal. A wrong reading means a new sensor; a normal reading sends the technician to the wiring.

Read the supporting manual

Does E71 stop all washing?

It may stop cycles that rely on heat. Cold cycles are not described on the sheet either way.

Read the supporting manual

How is E71 linked to E62 and E74?

Both of those temperature rows also start with test 13, because a bad reading from the sensor can cause either.

Read the supporting manual

The manual behind the message.

Manufacturer document

Washer Tech Data Sheet, A11200302 (1803)

Electrolux (technician sheet; retailer-hosted copy)

A11200302 (1803); 2018, 300/400/500/600 series (EFLS527UTT and EFLS627UTT copies are byte-identical) / p.2 (Washer Error Codes)

Row 71 of the washer sheet: select models. Test 13 (water NTC about 4.8K ohms).

Here to help

Good questions.
Clear answers.

Talk to our team
What is an NTC sensor?

It is a thermistor, a small sensor whose resistance falls as it warms. The control reads that resistance as water temperature.

Is E71 the heater itself?

No. It is the sensor that watches the water temperature. The heater rows are E66, E68, E69 and E6A.

Will E71 appear on the display?

No. The sheet marks it as not shown, so the first sign is usually a hot cycle that misbehaves or stops.

Is E71 urgent?

Not by itself. If the washer overheats, leaks or stops mid-cycle, stop using it and book a visit.

Let’s take care of it.

Premium appliances deserve
careful service.