Electrolux washer H1/B1 / Power supply

Electrolux washer
error H1/B1

Washer / display referenceH1/B1

H1 or B1 means the power frequency is out of limits, per Electrolux's 2018 washer sheet. The display shows it. Unplug the washer and book a technician; the sheet has the supply checked under load before any board is replaced.

Also shown as H1/B1

Last reviewed

Washer / display referenceH1/B1
Meaning
H1 or B1 means the power frequency is out of limits, per Electrolux's 2018 washer sheet. The display shows it. Unplug the washer and book a technician; the sheet has the supply checked under load before any board is replaced.
Who handles it
Model-dependent / read first
Related codes
Source
Washer Tech Data Sheet, A11200302 (1803)

What Electrolux washer H1/B1 means.

What it means

H1 or B1 means the power frequency is out of limits, per Electrolux's 2018 washer sheet. The display shows it. Unplug the washer and book a technician; the sheet has the supply checked under load before any board is replaced.

What you can safely check

Do not run a washer on a supply the control rejects.

When to call a technician

H1 or B1 returns after a power cycle.

Your checklist, kept on this device

Safe checks, in order.

0 of 5 checks done
  1. Electrolux washer H1/B1: Washer cord with a three-prong plug resting on a wood counter near a wall duplex outlet and a small surge protector, closed breaker panel behind
    Illustration. Follow your model’s instructions.
    Before you begin

    Unplug the washer

    Do not run a washer on a supply the control rejects. Leave it off until the supply has been checked.

  2. Washers in a thoughtfully designed home
    Illustration. Follow your model’s instructions.
    Check 2

    Think about the power source

    A generator, inverter or off-grid supply can have a frequency the washer does not accept. Say so when you book.

  3. A dark glass touch panel on a white front-load dryer, the display unlit
    Illustration. Follow your model’s instructions.
    Check 3

    Look at the outlet and cord

    Check for a loose plug, scorch marks or an extension cord. Remove any cord and plug straight into a wall outlet.

  4. Technician in navy coveralls holding a tablet with a blank checklist, a washer in the background.
    Illustration. Follow your model’s instructions.
    Check 4

    Write down both forms

    The sheet prints H1/B1. Note which one the display shows.

  5. A technician inspecting a front-load washer pump filter
    Illustration. Follow your model’s instructions.
    Check 5

    Book a visit

    Test 18 begins with the supply voltage under load, then the wiring to the main board, then the board itself.

Still showing H1/B1?

Send us the model and the checks you have done, and open your request here.

Book a visit

Fill and the water level.

Conceptual Washer sectionInlet valveTubLevel sensorDrain pump1234
  1. 1Inlet valve
  2. 2Tub

A simplified drawing, since layouts differ between models. Pick an outlined part for its photo and the related check.

A little more context.

What does H1/B1 mean?

The frequency of the incoming power is outside the limits the control accepts. The sheet's row reads frequency of power out of limits, and the display shows it.

Read the supporting manual

Why do two letters appear?

The sheet prints the code as H1/B1, one pair used on different displays. Both mean the same thing.

Read the supporting manual

What does a technician test?

Test 18: check the power in for voltage under load and correct any supply or branch-circuit problem; then check the power wiring to the main board; then wiring to the motor board for a short; then replace the main board.

Read the supporting manual

Is it safe to keep using?

Not until the supply is understood. An out-of-limits supply can stress the control and motor.

Read the supporting manual

The manual behind the message.

Manufacturer document

Washer Tech Data Sheet, A11200302 (1803)

Electrolux (technician sheet; retailer-hosted copy)

A11200302 (1803); 2018, 300/400/500/600 series (EFLS527UTT and EFLS627UTT copies are byte-identical) / p.2 (Washer Error Codes)

Row H1/B1 of the washer sheet: shown on the display. Tests 18 and 12.

Here to help

Good questions.
Clear answers.

Talk to our team
Could a generator cause H1/B1?

It can, if the generator's frequency drifts. The sheet does not mention generators, so this is a general risk we flag.

Is H1/B1 the same as H2/B2?

No. H1/B1 is frequency; H2/B2 is voltage too high. They share test 18. [1]

Why does the display show it?

The sheet's display column says yes for H1/B1, because running on a bad supply is a risk worth telling you about.

What do I tell you?

The model number, the exact characters shown and what powers your home.

Let’s take care of it.

Premium appliances deserve
careful service.