Maintenance

Washer fill problems: faucets, hose order, HO SE and the E11 lock

Hot and cold faucets must be on, the hoses must not be reversed, and the connections must be snug. A reversed pair triggers HO SE or F9, and a washer that cannot fill can lock out with E11 for up to 6 minutes. Fix the hoses first, then book if it persists.

Two braided hoses with red and blue bands running from wall faucets down behind a white washer.
Experienced techniciansWarranty on our workmanshipOEM parts available on orderUpfront pricing, agreed before work
On this page
Key points
  • Pressure must be 30 to 120 psi, with no more than a 10 psi difference between hot and cold. 1
  • Water should start filling within 2 minutes of pressing Start. 1
  • Reversed hoses raise HO SE; the technician sheet calls the same warning F9. 24
  • E11 can lock the washer for up to 6 minutes, and unplugging restarts the lock. 3
  • For a washer under a month old, Electrolux sends you to the installer. 13

What does an Electrolux washer need from the water supply?#

Two working faucets within hose reach, 3/4 inch with threading for a laundry hose, pressure between 30 and 120 psi, and no more than 10 psi of difference between hot and cold. Both must be turned on, or the washer will not work properly. 1

Your local water department can tell you the pressure at your address. The guide gives the numbers and no test method, so we do too. 1

Electrolux also notes that hoses are not included with the washer. If you are replacing them, use new hoses and make sure the rubber washers are present. 1

What should a normal fill look like?#

Water should start filling within 2 minutes of pressing Start. If nothing arrives, Electrolux's guide starts with whether the hot and cold hoses are reversed, then whether the hoses are snug, whether water flows freely at the faucets, and whether the inlet filters are clean. 1

Do those in order, because each one takes less time than the next. A quick way to separate a supply problem from a washer problem is to turn the water off, disconnect a hose into a bucket and turn the faucet on. If water runs freely, the house side is fine. 1

  1. 1

    Confirm both faucets are fully open#

    The washer will not function properly if either is closed. 1

    Two wall faucets with red and blue lever handles and gray braided hoses attached, on white tile.
  2. 2

    Check which hose is which#

    Hot supply to the hot inlet, cold to the cold inlet. The guide says reversed hoses are the first thing to rule out when no water arrives. 1

  3. 3

    Tighten, but only as far as the guide says#

    Hand-tight until snug, then another two-thirds of a turn with pliers. Do not cross-thread or over-tighten. 1

  4. 4

    Look at the filters on the inlet connectors#

    Turn the water off, disconnect the hoses and look at the filters. Run both faucets briefly first to flush particles out of the lines. 1

    Fingers holding a small round mesh screen with grit on it beside the threaded end of a washer hose.
  5. 5

    Swap flood-safe hoses#

    If you use flood-safe hoses, the guide says to replace them with standard washer hoses for this problem. 1

  6. 6

    Straighten the hoses#

    When you push the washer back, make sure no hose is bent, kinked or pinched. 1

What do HO SE and F9 mean?#

Both are the reversed-hose warning. On the Owner Center, HO SE means the washer detected hot supply on the cold inlet and cold supply on the hot inlet. The technician sheet prints the same condition as F9: hot valve warning, hot and cold hoses reversed. 24

The display detail matters. The Owner Center says the LED shows HO, then SE, then 0 min for 60 seconds, then repeats. Press Cancel, shut off each water supply valve and attach each hose to the correct inlet. 2

The sheet's F9 is not shown to the user on its display column, and its next step reads: reverse the water hoses to reduce the risk of water temperature related problems with the load. 4

For a washer under a month old, Electrolux sends you back to the installer. After that you can book with us. 2

Our HO SE code page and F9 entry list the same warning alongside the other washer codes.

How can reversed hoses end in an E11?#

E11 means the washer is not filling during the wash phase. The Owner Center says it can lock the unit for up to 6 minutes and lists reversed hot and cold lines first, then the supply requirements. The sheet gives E11 as Fill time too long and shows it to the user. 34

Two details from the article save time:

  • Unplugging and plugging back in restarts the 6-minute lock. Wait it out. 3
  • The article calls reversed lines a known installation issue, so a washer that was just installed or moved is one for the installer to check. 3
What you seeWhat Electrolux saysWhere
HO SE, then 0 minHoses reversed; cancel, shut off water, reconnect correctlyKB 1829275 2
F9Hot valve warning, hoses reversed (technician sheet)Sheet 4
E11, unit lockedNot filling; lock up to 6 minutes; check hose order and supplyKB 1820068 3

Our E11 page covers the fill-time code on its own.

What if water is leaking at the hose instead?#

Turn the water off, wipe up, and look at the inlet hose and its connections. The leak article says to check for kinks or holes, inspect the O-ring gasket for damage, look at the blue or red connector on the washer for cracks, then hand-tighten and add a half turn with a wrench. 5

Notice the two different tightening figures. The supply guide says two-thirds of a turn with pliers for a new hose connection. The leak article says a half turn with a wrench after you have re-seated an O-ring. Both stop short of over-tightening. 15

A cracked or broken connector on the washer means a visit. The article says cracks and breaks are normally caused by over-tightening. 5

Two gray washer hoses with red and blue bands connected to the back panel of a white washer.
Match the hose to the inlet it came from at the faucet.

Water that leaks from the drawer or the door is a different problem. The same article says to check that the dispenser drawer is closed and seated, and that high pressure can leak at the dispenser, in which case it suggests turning the faucet to 50 percent. 5

When should a technician handle the fill problem?#

Book when the washer still will not fill after the faucets, hoses and filters check out, when an inlet connector is cracked, or when HO SE or E11 returns once the hoses are right. A technician can test the fill valve and look at the supply side. 135

Next step: \book a visit\, or look over our washer service. The technician agrees the price with you before any work starts. The exact cost is confirmed after the on-site diagnostic. If your unit is under the manufacturer's warranty, the manufacturer handles that repair. We give a warranty on our workmanship.

Sources#

  1. Laundry Water Supply Guide (KB 1820069)Electrolux / Owner Center knowledge base (owner.electrolux.com) · Owner Center article, cached 10.11.2026 (no edition date printed) · article text
  2. Laundry front loading washer displaying Error Code HO SE reversed hose detection. (KB 1829275)Electrolux / Owner Center knowledge base (owner.electrolux.com) · Owner Center article, cached 10.11.2026 (no edition date printed) · article text
  3. Laundry front loading washer displaying Error Code E11 long fill time. (KB 1820068)Electrolux / Owner Center knowledge base (owner.electrolux.com) · Owner Center article, cached 10.11.2026 (no edition date printed) · article text
  4. Washer Tech Data Sheet, A11200302 (1803)Electrolux (technician sheet; retailer-hosted copy) · A11200302 (1803); 2018, 300/400/500/600 series · p.3-4 (Washer Error Codes: 11 and F9)
  5. Laundry front loading washer is leaking water. (KB 1831358)Electrolux / Owner Center knowledge base (owner.electrolux.com) · Owner Center article, cached 10.11.2026 (no edition date printed) · article text

Here to help

Good questions.
Clear answers.

Talk to our team
How much water pressure should an Electrolux washer get?

Between 30 and 120 psi, with no more than 10 psi of difference between the hot and cold lines. Your local water department can tell you the pressure at your address. [1]

How tight should the hose connections be?

Hand-tight until snug, then another two-thirds turn with pliers. Electrolux warns against cross-threading and over-tightening, and says new hoses with their rubber washers should be used. [1]

Will unplugging the washer clear an E11?

No. E11 can lock the washer for up to 6 minutes, and unplugging and plugging it back in restarts that 6-minute lock. Check the hoses and the faucets instead. [3]

Do flood-safe hoses work with this washer?

Not for a fill problem. The supply guide says that if you use flood-safe hoses, replace them with standard washer hoses when the washer will not take water. [1]

Who deals with a hose problem on a new install?

On a washer under a month old, Electrolux points you to the installer. Past that point you can book a visit with us. [1][2][3]

Let’s take care of it.

Premium appliances deserve
careful service.