Start from the symptom
Electrolux dryer runs but does not heat.
A drum that turns without heat often means one of the two house circuits feeding an electric dryer has tripped. Electrolux also lists the cycle choice, a 240-volt supply and, on gas models, the gas valve, the propane tank and the air around the dryer.

Start with safe observations.
Power the appliance down and pull the plug before any owner check. Beware of standing water and sharp debris. Never touch a wet plug or electrical area, take off service panels, or step beyond your model’s owner guide.
- 1
Look at both breakers or fuses
An electric dryer uses two house circuits or fuses. When one is tripped or blown, the drum can still turn while the heater gets nothing. Switch the breaker back on, or swap in a fuse of identical rating, never a larger one.
- 2
Read the cycle and temperature
On Air Fluff, or the air-only temperature, the drum turns with no heat at all. Electrolux suggests low or medium heat with a normal dry setting.
- 3
Voltage at the outlet
Electrolux wants a qualified electrician to confirm that the outlet supplies 240 volts. Its drying-time article adds that 208 volts, rather than 240, makes drying take longer.
- 4
Gas dryer: supply
Confirm the shutoff valve on the gas line is open. On propane, check that the tank is not empty. After an interruption in natural gas service, Electrolux says to call the gas company. If you smell gas, leave the dryer off, go outside and call your gas utility.
- 5
Gas dryer: room around it
The burner needs air to run properly. Keep laundry and rugs away from the front and the back of the dryer.
- 6
Weak heat rather than none
Clean the lint screen after every use, wipe the moisture sensor bars with rubbing alcohol if softener sheets left a film, and clear the exhaust duct and hood. Do not operate a gas dryer lacking a duct that carries exhaust outside; carbon monoxide is the danger.
- 7
Heat codes
On Electrolux's dryer sheet, E61 is a heater relay failure, E64 an open heater circuit and E66 an open thermal limiter. All three need a technician.
Systems a technician may investigate.
The parts below tie in with this symptom. Seeing it does not prove any one of them has failed.

Dryer heater relay
A heater relay is the switch that sends power to the dryer’s heating element. Electrolux’s dryer sheet ties E61 to it: the relay stuck open or closed, or the wiring around it defective. A technician tests it with the cycle stopped.

Dryer thermal limiter
The thermal limiter is a temperature safety part in the dryer’s heated air path. When it opens, the circuit stops. Electrolux’s dryer sheet names the outlet limiter (plus an inlet limiter on gas models) behind E66, and an inlet limiter on electric models behind E65.
If the display adds a code.
Heating
E61 is a heater relay failure on Electrolux's dryer chart: a heater relay is stuck open or closed, or the wiring is defective. If the dryer runs without heat, or heats when it should not, unplug it and book a technician.
Heating
E64 is an open circuit in the heater on Electrolux's dryer chart: the heating element or its wiring is defective. The dryer may tumble with no heat. Check the cycle and the breakers, then book a technician.
Heating
E66 means a thermal limiter is open on Electrolux's dryer chart: the outlet limiter has tripped, or on gas models the inlet limiter, or the wiring is defective. Unplug the dryer and book a technician; do not bridge the limiter.
Read the related care guide.

A code on the dryer? Recall it, then read its group.
To see the last code on an Electrolux dryer, wake it with any button except cancel, then hold cancel and start/pause for 6 seconds. Codes sort by their first digit into contact sensor, motor, heat, thermistor, board, supply and airflow groups, and most groups need a technician.

E61, E64, E65 or E66? Each one tests something different.
On an Electrolux dryer, E61 is the heater relay, E63 a heater short to ground, E64 an open heater circuit, E65 a high-limit thermostat that tripped too often and E66 an open thermal limiter. Only E65 sends the technician to the vent, and every one of them needs a visit.
When observation becomes a service request.
Leave internal testing to a technician.
If both breakers are fine, the settings are right and the dryer still will not heat, or if E61, E64 or E66 appears, book a technician. We can test the heater circuit and the thermal limiter. With any gas smell, stop first and call the gas utility.
Arrange a diagnosticSources and model boundaries.
These sources back the Electrolux dryer runs but does not heat guidance. Use the manual for your own model.
- My dryer is running, but does not seem to be heating. What should I do? (KB 1853007)
- Dryer - Not Drying and Extended Drying Time (KB 1853008)
- Dryer Tech Data Sheet, P/N 137265000B (1202)
Follow the guide for your exact model. Consult how we research these pages.
My dryer turns yet stays cold. Why?
On an electric dryer, one tripped breaker or blown fuse can leave the drum turning with no power to the heater. Check both house circuits first.
Can the Air Fluff setting cause no heat?
Yes. With Air Fluff the laundry tumbles but is not heated. Pick low or medium heat with a normal dry setting and start again.
My gas dryer does not heat. What should I check?
Open the gas valve and, on propane, look at the tank. Leave room around the dryer for burner air. Smell gas? Stop, go outside and call your gas utility.
Does E64 mean the heating element failed?
The sheet describes E64 as an open circuit in the heating element or its wiring. It points at the heater circuit, and a technician confirms which part has failed.
Codes, symptoms, parts and service
Link the message to what to do next.
E61
E61 is a heater relay failure on Electrolux's dryer chart: a heater relay is stuck open or closed, or the wiring is defective. If the dryer runs without heat, or heats when it should not, unplug it and book a technician.
Electrolux dryer noisy, rattling or shaking
Most dryer noise has a simple source: coins or buckles in the drum, a loose pedestal, shipping bolts still in place or a dryer that is out of level. Electrolux also lists sounds that are normal, such as the chime at the end of a cycle.
Dryer heater relay
A heater relay is the switch that sends power to the dryer’s heating element. Electrolux’s dryer sheet ties E61 to it: the relay stuck open or closed, or the wiring around it defective. A technician tests it with the cycle stopped.
Dryer repair
Book a diagnostic for your model at the appliance.
Find your metro
Office details and the access information to pass on.