Before work starts
The technician examines the appliance, tells you what the repair involves and agrees the cost with you before opening anything up.
Independent appliance repair
We repair Electrolux electric and gas dryers that run without heat, stop mid-cycle, dry slowly, make noise or show an E or EF code. Tell us the code and what the drum does, then book a technician.


Most dryer noise has a simple source: coins or buckles in the drum, a loose pedestal, shipping bolts still in place or a dryer that is out of level. Electrolux also lists sounds that are normal, such as the chime at the end of a cycle.

A drum that turns without heat often means one of the two house circuits feeding an electric dryer has tripped. Electrolux also lists the cycle choice, a 240-volt supply and, on gas models, the gas valve, the propane tank and the air around the dryer.

Overheating and over-drying nearly always come down to settings or airflow. Electrolux's advice is the right cycle, Auto Dry in place of Timed Dry, a clean lint screen and a clear exhaust. Its E65 and EF1 codes both start with a restricted vent.

A dryer that will not start is usually waiting for a simple condition: the start control held long enough, the door fully shut, power at the plug, or a breaker that is still on. Electrolux also says a hot motor must rest for 30 minutes.

If the dryer runs but the drum stays still, or the motor will not start, the sheet points at the motor circuit: E52 for a motor that stopped or did not start, E51 for the motor relay, E53 for the centripetal switch and E54 for motor sensing. Load size and power supply come first.
E61 is a heater relay failure on Electrolux's dryer chart: a heater relay is stuck open or closed, or the wiring is defective. If the dryer runs without heat, or heats when it should not, unplug it and book a technician.
E64 is an open circuit in the heater on Electrolux's dryer chart: the heating element or its wiring is defective. The dryer may tumble with no heat. Check the cycle and the breakers, then book a technician.
E65 means the high limit thermostat has tripped too many times, per Electrolux's dryer chart. The chart lists a restricted vent first, then the thermostat or, on electric models, the inlet thermal limiter. Clean the lint screen and vent, then book a technician.
E66 means a thermal limiter is open on Electrolux's dryer chart: the outlet limiter has tripped, or on gas models the inlet limiter, or the wiring is defective. Unplug the dryer and book a technician; do not bridge the limiter.
E71 means the outlet control thermistor is open circuit, per Electrolux's dryer chart. A technician checks its resistance, which should be 4.9K to 6.2K ohms at room temperature, and the wiring. Book a visit; the dryer may stop or misjudge heat.
E73 means the inlet control thermistor is open circuit, per Electrolux's dryer chart. A technician checks its resistance, which should be 47K to 66K ohms at room temperature, and the wiring. Book a visit.
EF1 on an Electrolux dryer means the vent is blocked. The chart calls it vent blocked and the Owner Center guide calls it ventilation blockage, a known installation issue. Clean the lint filter, check the exhaust tube and the vent exit.
EF3 is a maximum timeout timer on Electrolux's dryer chart: the cycle ran to its time limit. The sheet lists a blocked exhaust first, then the exhaust or inlet thermistor, the contact sensor or the board. Check the vent, then book a technician.
E52 means the dryer motor stopped or will not start, per Electrolux's dryer chart. The listed conditions are an overheated motor, a load that is too heavy, low supply voltage, or a defective motor or wiring. Take the load out and let it cool.
E91 is a communication error between the dryer's control board and its interface board, per Electrolux's dryer chart. The cause is the wiring, the control board or the interface board. Restart once, then book a technician.
The linked parts are the ones Electrolux’s technician sheets name for this appliance. We confirm each against your model number once the diagnostic is done, and you approve any replacement first.

A heater relay is the switch that sends power to the dryer’s heating element. Electrolux’s dryer sheet ties E61 to it: the relay stuck open or closed, or the wiring around it defective. A technician tests it with the cycle stopped.

The thermal limiter is a temperature safety part in the dryer’s heated air path. When it opens, the circuit stops. Electrolux’s dryer sheet names the outlet limiter (plus an inlet limiter on gas models) behind E66, and an inlet limiter on electric models behind E65.

The high-limit thermostat is a second temperature guard inside the dryer. Code E65 means the control has counted too many of its trips. Electrolux’s sheet blames a high vent restriction first, then the thermostat itself, then the inlet limiter on electric models.

Control thermistors are the temperature sensors that tell the dryer how hot the air is. Electrolux’s sheet names an outlet, an inlet and an exhaust thermistor. E71 to E74 mean an open or shorted sensor circuit, and EF1 and EF3 list them among the causes.

The contact sensor reads how damp the load is. Electrolux’s dryer sheet labels its test row “MOIST. BARS” and ties E31 and E32 to a frequency reading that is too high or too low. A foreign object touching the sensor is one listed cause.
How a repair visit runs.
Measured and clear.

Name the washer, dryer or oven and say what it does. Add the code on the screen if there is one.

The technician runs the cycle, checks the parts behind the code and explains the cost before starting.

The part is replaced, a test cycle confirms the fix, and the technician walks you through the result.
Wake the dryer with any button except Cancel, then hold Cancel and Start/Pause for 6 seconds. The display shows E and two digits, or E00 if none is stored.
Electric dryers draw on two house circuits, so one tripped breaker can leave the heater dead while the drum still turns. Electrolux adds that the Air Fluff setting never heats.
Electrolux wants the screen cleared around every load and the whole outdoor vent run cleaned each 18 months. The hood should have a damper flap, no mesh across it, and 12 inches of ground clearance.
If the dryer stopped, Electrolux says to wait 30 minutes for an overheated motor. An average washer load fills a third to a half of the drum.
On a gas model, confirm the supply valve is open and any LP tank holds fuel. Electrolux warns of carbon monoxide if a gas dryer runs with no outdoor exhaust duct.
Book a technician if a code returns after the lint, vent and breaker checks, or if the dryer keeps stopping or never heats.
Book a technician for E61, E64, E65, E66, E71 to E74, EF1 or EF3. Each one points at a heating, sensing or airflow part that needs meter work.
Gas dryer owners who smell gas should stop the dryer, avoid switches and flames, go outside and phone the gas supplier.
Panels, wiring and gas connections stay with the technician.
Arrange a diagnosticThe technician examines the appliance, tells you what the repair involves and agrees the cost with you before opening anything up.
An Electrolux still under its manufacturer warranty goes to Electrolux for covered repairs. Our repairs carry a warranty on our workmanship.
The usual leads are a tripped house breaker, a no-heat cycle and, on gas models, the gas supply. A code such as E61 or E64 points at the heating circuit. Book a technician if the checks change nothing.
The sheet calls it Vent Blocked and the owner article Ventilation Blockage. Clean the lint screen, the duct and the hood. If it returns, book a visit so the sensors are checked as well.
Electrolux lists a dirty lint screen, a blocked vent, a load that is too big or too small, a film on the moisture bars and a 208-volt supply, which lengthens drying. Book a visit if cleaning does not help.
Yes. Say which fuel your dryer uses when you book, since a few codes differ by model; E66, for example, also covers an inlet limiter on gas models.
If your unit is under the manufacturer’s warranty, the manufacturer handles that repair.
Codes, symptoms, parts and service
E61 is a heater relay failure on Electrolux's dryer chart: a heater relay is stuck open or closed, or the wiring is defective. If the dryer runs without heat, or heats when it should not, unplug it and book a technician.
Most dryer noise has a simple source: coins or buckles in the drum, a loose pedestal, shipping bolts still in place or a dryer that is out of level. Electrolux also lists sounds that are normal, such as the chime at the end of a cycle.
A heater relay is the switch that sends power to the dryer’s heating element. Electrolux’s dryer sheet ties E61 to it: the relay stuck open or closed, or the wiring around it defective. A technician tests it with the cycle stopped.
Book a diagnostic for your model at the appliance.
Office details and the access information to pass on.