Start from the symptom
Electrolux dryer drum not turning.
If the dryer runs but the drum stays still, or the motor will not start, the sheet points at the motor circuit: E52 for a motor that stopped or did not start, E51 for the motor relay, E53 for the centripetal switch and E54 for motor sensing. Load size and power supply come first.

Start with safe observations.
Power the appliance down and pull the plug before any owner check. Beware of standing water and sharp debris. Never touch a wet plug or electrical area, take off service panels, or step beyond your model’s owner guide.
- 1
Give the motor time
Electrolux says an overloaded motor can overheat and that it needs about 30 minutes to cool down. The sheet adds that a tripped motor thermal protector may take up to 30 minutes to reset.
- 2
Cut the load
Electrolux says a typical washer load fills the drum between one-third and one-half. Take some laundry out before you try again.
- 3
Check the power
The sheet lists low power supply among the causes of E52. Look at the breaker and the plug. Electrolux warns against extension cords and says a blown fuse must be replaced at its original capacity.
- 4
Close the door
A door that is not fully shut keeps the dryer from running. Electrolux also lists E42 for door trouble.
- 5
Recall the stored code
The Electrolux dryer sheet describes showing the last stored error by holding cancel and start pause together for 6 seconds after waking the dryer. E00 means none was recorded. Note the code for the technician.
- 6
Do not work inside
The sheet lists the motor, the relay, the centripetal switch and the control board among the parts behind these codes. Those are technician jobs, with power disconnected.
Systems a technician may investigate.
The parts below tie in with this symptom. Seeing it does not prove any one of them has failed.
If the display adds a code.
Motor
E52 means the dryer motor stopped or will not start, per Electrolux's dryer chart. The listed conditions are an overheated motor, a load that is too heavy, low supply voltage, or a defective motor or wiring. Take the load out and let it cool.
Motor
E51 is a motor relay failure on Electrolux's dryer chart: the relay that switches the motor is stuck open or closed, or its wiring is defective. Unplug the dryer and book a technician; the chart's tests need the cabinet open.
Motor
E53 is a motor centripetal switch failure on Electrolux's dryer chart. The switch inside the motor, the control board or the wiring is defective. Unplug the dryer and book a technician; the chart's fixes are wiring checks and parts.
Motor
E54 is a motor sensing failure on Electrolux's dryer chart. The chart's only listed condition is a defective electronic control board, and the solution is to replace it and retest. Book a technician.
Read the related care guide.

A code on the dryer? Recall it, then read its group.
To see the last code on an Electrolux dryer, wake it with any button except cancel, then hold cancel and start/pause for 6 seconds. Codes sort by their first digit into contact sensor, motor, heat, thermistor, board, supply and airflow groups, and most groups need a technician.

E61, E64, E65 or E66? Each one tests something different.
On an Electrolux dryer, E61 is the heater relay, E63 a heater short to ground, E64 an open heater circuit, E65 a high-limit thermostat that tripped too often and E66 an open thermal limiter. Only E65 sends the technician to the vent, and every one of them needs a visit.
When observation becomes a service request.
Leave internal testing to a technician.
When the drum stays put after a cool-down and a smaller load, or E51, E52, E53 or E54 returns, book a technician. Tell us the stored code and whether the motor hums, clicks or stays silent.
Arrange a diagnosticSources and model boundaries.
These sources back the Electrolux dryer drum not turning guidance. Use the manual for your own model.
- Dryer Tech Data Sheet, P/N 137265000B (1202)
- What should I do if my dryer stops operating? (KB 1853011)
- What should I do if my dryer does not start? (KB 1853009)
Follow the guide for your exact model. Consult how we research these pages.
Why is my dryer on but the drum is still?
Motor trouble is the usual link. The Electrolux sheet lists E52 for a motor that stopped or did not start, and its causes include overheating, a heavy load and low power supply.
How long should the motor cool down?
Electrolux says to allow 30 minutes if the motor overheated, and the sheet gives the same figure for a tripped motor thermal protector to reset.
What is the difference between E51 and E52?
E51 is a motor relay failure, with the relay stuck open or closed or the wiring defective. E52 is the motor itself stopping or failing to start.
Can I see the last error code on my dryer?
The sheet describes it: wake the dryer with any button except cancel, then hold cancel and start pause for 6 seconds. E00 means no failure was recorded.
Codes, symptoms, parts and service
Link the message to what to do next.
E52
E52 means the dryer motor stopped or will not start, per Electrolux's dryer chart. The listed conditions are an overheated motor, a load that is too heavy, low supply voltage, or a defective motor or wiring. Take the load out and let it cool.
Electrolux dryer noisy, rattling or shaking
Most dryer noise has a simple source: coins or buckles in the drum, a loose pedestal, shipping bolts still in place or a dryer that is out of level. Electrolux also lists sounds that are normal, such as the chime at the end of a cycle.
Dryer thermal limiter
The thermal limiter is a temperature safety part in the dryer’s heated air path. When it opens, the circuit stops. Electrolux’s dryer sheet names the outlet limiter (plus an inlet limiter on gas models) behind E66, and an inlet limiter on electric models behind E65.
Dryer repair
Book a diagnostic for your model at the appliance.
Find your metro
Office details and the access information to pass on.
