What it means
E53 is a motor centripetal switch failure on Electrolux's dryer chart. The switch inside the motor, the control board or the wiring is defective. Unplug the dryer and book a technician; the chart's fixes are wiring checks and parts.
Electrolux dryer E53 / Motor
E53 is a motor centripetal switch failure on Electrolux's dryer chart. The switch inside the motor, the control board or the wiring is defective. Unplug the dryer and book a technician; the chart's fixes are wiring checks and parts.
Also shown as E53
E53 is a motor centripetal switch failure on Electrolux's dryer chart. The switch inside the motor, the control board or the wiring is defective. Unplug the dryer and book a technician; the chart's fixes are wiring checks and parts.
The centripetal switch sits inside the motor and the circuit carries line voltage.
E53 returns or the drum will not start.
Your checklist, kept on this device

The centripetal switch sits inside the motor and the circuit carries line voltage. Disconnect power before anything else.

Does the drum fail to start, or stop after running a moment? The pattern helps the technician.

There is nothing for an owner to adjust on the switch.

Use any button but Cancel to wake it up, then hold Cancel and Start/Pause together for a six-second count.

The chart checks the wiring, tests whether the switches are stuck open or closed, and then replaces the motor and, if needed, the control board.
Send us the model and the checks you have done, and open your request here.
Book a visit
A simplified drawing, since layouts differ between models. Pick an outlined part for its photo and the related check.

Component reference
The dryer electronic control board is the main board of an Electrolux front-load dryer, and the interface board is the console board that talks to it.
Read the definitionThe motor's centripetal switch has failed. The chart lists three possible conditions: the switch, the electronic control board or defective wiring.
Read the supporting manualA switch in the motor that changes state as the motor reaches speed. The chart does not explain it further, so we say only what it lists.
Read the supporting manualCheck wiring; check whether the switches are stuck open or closed; replace the motor; replace the electronic control board. In that order.
Read the supporting manualNo. A motor circuit that cannot confirm its start switch should not be forced.
Read the supporting manualManufacturer document
Electrolux (technician sheet; retailer-hosted copy)
P/N 137265000B (1202); Canadian SKU EIMED6CJIW; original file dated 2009 / sheet p.1 (Error Code Chart)
Row E53 of the dryer chart, page 1.
The chart names no lint cause for E53. Its conditions are the switch, the control board and the wiring, so lint is not on its list.
The chart lists it as the step after wiring and the switch check, so it is possible.
Yes. E54 is motor sensing, which the chart fixes by replacing the control board.
For E53, the model number and what the drum did before the code appeared.
Codes, symptoms, parts and service
E52 means the dryer motor stopped or will not start, per Electrolux's dryer chart. The listed conditions are an overheated motor, a load that is too heavy, low supply voltage, or a defective motor or wiring. Take the load out and let it cool.
Most dryer noise has a simple source: coins or buckles in the drum, a loose pedestal, shipping bolts still in place or a dryer that is out of level. Electrolux also lists sounds that are normal, such as the chime at the end of a cycle.
The dryer electronic control board is the main board of an Electrolux front-load dryer, and the interface board is the console board that talks to it. Electrolux's dryer chart names the control board for E54, E67, E94, E97 and EA5, and the pair for E91 to E93. Owners can restart the dryer once; board work is for a technician.
Book a diagnostic for your model at the appliance.
Office details and the access information to pass on.