Inside the appliance
Dryer thermal limiter. In plain English.
The thermal limiter is a temperature safety part in the dryer’s heated air path. When it opens, the circuit stops. Electrolux’s dryer sheet names the outlet limiter (plus an inlet limiter on gas models) behind E66, and an inlet limiter on electric models behind E65.

Where it fits.
Dryer thermal limiter in the appliance
The sheet mentions an outlet limiter, and an inlet limiter on gas models; for E65 on electric models it checks an inlet limiter too. The documents give no position, so a technician finds each one by model.
The image shows the type of component only. It does not select a replacement that fits your model.
What is different once this system needs attention.
Dryer thermal limiter concerns may show up with a drop in performance or a code that keeps returning. Testing comes first before anyone decides the component has failed.

Electrolux dryer runs but does not heat
A drum that turns without heat often means one of the two house circuits feeding an electric dryer has tripped. Electrolux also lists the cycle choice, a 240-volt supply and, on gas models, the gas valve, the propane tank and the air around the dryer.

Electrolux dryer overheating or drying too much
Overheating and over-drying nearly always come down to settings or airflow. Electrolux's advice is the right cycle, Auto Dry in place of Timed Dry, a clean lint screen and a clear exhaust. Its E65 and EF1 codes both start with a restricted vent.
Owner care, within the model instructions.
Power the appliance down and pull the plug before any owner check. Beware of standing water and sharp debris. Never touch a wet plug or electrical area, take off service panels, or step beyond your model’s owner guide.
- 1
Clear lint and vent first
KB 1847456 wants the lint screen cleared before or after every load, and the outdoor exhaust and venting cleaned every 18 months. The sheet’s E65 row puts a high vent restriction first when a thermal limiter has opened.
- 2
Let the motor cool
KB 1853011 says an overheated motor needs 30 minutes to cool. The article puts an average washer load at a third to a half of the drum.
- 3
Note what ran before
If the dryer stopped mid-cycle, write down the cycle, the load size and whether E66 or E65 appeared. The sheet asks a technician to look for signs of a high-temperature event.
- 4
Do not reset it yourself
KB 1853011 says a tripped thermal limiter switch on an electric dryer needs a service provider to replace it. It is not a button you can press.
Cleaning or replacement?
Leave internal testing to a technician.
Book a technician if the dryer stops, shows E66 or E65, or runs without heat after the vent is clear and the motor has cooled.
Arrange a diagnosticSources and model boundaries.
These sources back the Dryer thermal limiter guidance. Use the manual for your own model.
- Dryer Tech Data Sheet, P/N 137265000B (1202)
- What should I do if my dryer stops operating? (KB 1853011)
- Dryers - How often do I need to clean my dryer or the lint screen/filter to optimize my drying performance? (KB 1847456)
Follow the guide for your exact model. Consult how we research these pages.
What does E66 mean on my Electrolux dryer?
The sheet prints Thermal Limiter Open Circuit. The outlet limiter has tripped, or its wiring is open. On gas models the inlet limiter is also checked.
Why would a thermal limiter open?
The sheet lists the limiter tripping or defective wiring. For the related E65 row it puts a high vent restriction first, which is why a technician checks the exhaust.
Is a tripped limiter safe to bypass?
No. It is a safety part. The sheet’s step is to check for damage from a high-temperature event and replace the limiter if nothing else is harmed, then retest.
Can I just replace the limiter and carry on?
Only after the cause is found. The sheet checks continuity first, then looks for damage, and the E65 row sends the technician to the exhaust path if the limiter itself is fine.
Codes, symptoms, parts and service
Link the message to what to do next.
E66
E66 means a thermal limiter is open on Electrolux's dryer chart: the outlet limiter has tripped, or on gas models the inlet limiter, or the wiring is defective. Unplug the dryer and book a technician; do not bridge the limiter.
Electrolux dryer noisy, rattling or shaking
Most dryer noise has a simple source: coins or buckles in the drum, a loose pedestal, shipping bolts still in place or a dryer that is out of level. Electrolux also lists sounds that are normal, such as the chime at the end of a cycle.
Dryer repair
Book a diagnostic for your model at the appliance.
Find your metro
Office details and the access information to pass on.
