Start from the symptom
Electrolux dryer overheating or drying too much.
Overheating and over-drying nearly always come down to settings or airflow. Electrolux's advice is the right cycle, Auto Dry in place of Timed Dry, a clean lint screen and a clear exhaust. Its E65 and EF1 codes both start with a restricted vent.

Start with safe observations.
Power the appliance down and pull the plug before any owner check. Beware of standing water and sharp debris. Never touch a wet plug or electrical area, take off service panels, or step beyond your model’s owner guide.
- 1
Match the cycle to the fabric
For over-dried laundry Electrolux keeps it short: choose the proper cycle and temperature, follow the fabric care labels and try Auto Dry rather than Timed Dry.
- 2
Clean the lint screen every load
Electrolux says to clean it before or after each load. Heavy lint blocks airflow and drying suffers.
- 3
Follow the exhaust path
The code guide for EF1 says to check the lint filter, look along the exhaust tube for bends, restrictions and blocks, and clear the vent exit. Electrolux calls EF1 a known installation issue.
- 4
Clean the whole vent system
Electrolux recommends cleaning the full outdoor exhaust and venting about every 18 months. A gas dryer needs a duct that carries exhaust outdoors; without one, carbon monoxide is a danger.
- 5
If the dryer stopped mid-cycle
An overloaded motor can overheat. Electrolux's advice is a 30-minute rest and a smaller load, aiming for a drum that is one-third to one-half full. On electric dryers a thermal limiter can also shut the motor off.
- 6
What E65 means
The dryer sheet describes E65 as the high-limit thermostat tripping too many times. It lists a high vent restriction first, then the thermostat itself or, on electric models, the inlet thermal limiter.
Systems a technician may investigate.
The parts below tie in with this symptom. Seeing it does not prove any one of them has failed.

Dryer high-limit thermostat
The high-limit thermostat is a second temperature guard inside the dryer. Code E65 means the control has counted too many of its trips. Electrolux’s sheet blames a high vent restriction first, then the thermostat itself, then the inlet limiter on electric models.

Dryer thermal limiter
The thermal limiter is a temperature safety part in the dryer’s heated air path. When it opens, the circuit stops. Electrolux’s dryer sheet names the outlet limiter (plus an inlet limiter on gas models) behind E66, and an inlet limiter on electric models behind E65.

Dryer control thermistor
Control thermistors are the temperature sensors that tell the dryer how hot the air is. Electrolux’s sheet names an outlet, an inlet and an exhaust thermistor. E71 to E74 mean an open or shorted sensor circuit, and EF1 and EF3 list them among the causes.
If the display adds a code.
Heating
E65 means the high limit thermostat has tripped too many times, per Electrolux's dryer chart. The chart lists a restricted vent first, then the thermostat or, on electric models, the inlet thermal limiter. Clean the lint screen and vent, then book a technician.
Airflow
EF1 on an Electrolux dryer means the vent is blocked. The chart calls it vent blocked and the Owner Center guide calls it ventilation blockage, a known installation issue. Clean the lint filter, check the exhaust tube and the vent exit.
Heating
E66 means a thermal limiter is open on Electrolux's dryer chart: the outlet limiter has tripped, or on gas models the inlet limiter, or the wiring is defective. Unplug the dryer and book a technician; do not bridge the limiter.
Airflow
EF3 is a maximum timeout timer on Electrolux's dryer chart: the cycle ran to its time limit. The sheet lists a blocked exhaust first, then the exhaust or inlet thermistor, the contact sensor or the board. Check the vent, then book a technician.
Read the related care guide.

A code on the dryer? Recall it, then read its group.
To see the last code on an Electrolux dryer, wake it with any button except cancel, then hold cancel and start/pause for 6 seconds. Codes sort by their first digit into contact sensor, motor, heat, thermistor, board, supply and airflow groups, and most groups need a technician.

E61, E64, E65 or E66? Each one tests something different.
On an Electrolux dryer, E61 is the heater relay, E63 a heater short to ground, E64 an open heater circuit, E65 a high-limit thermostat that tripped too often and E66 an open thermal limiter. Only E65 sends the technician to the vent, and every one of them needs a visit.
When observation becomes a service request.
Leave internal testing to a technician.
If the dryer still runs hot with a clear lint screen and vent, or E65, EF1 or EF3 keeps coming back, book a visit. If the cabinet feels very hot or you smell something burning, stop using it until a technician has looked.
Arrange a diagnosticSources and model boundaries.
These sources back the Electrolux dryer overheating or drying too much guidance. Use the manual for your own model.
- My clothes seem to be over-dried. How can I prevent this? (KB 1853006)
- Dryers - How often do I need to clean my dryer or the lint screen/filter to optimize my drying performance? (KB 1847456)
- Laundry Dryer Error Code Guide (KB 1820071)
- What should I do if my dryer stops operating? (KB 1853011)
- Dryer Tech Data Sheet, P/N 137265000B (1202)
Follow the guide for your exact model. Consult how we research these pages.
How do I stop my dryer from over-drying?
Pick the cycle and temperature that suit the fabric, follow the care labels, and switch from Timed Dry to Auto Dry. That is Electrolux's own advice.
How frequently does the vent need cleaning?
Electrolux advises cleaning the lint screen with every load and the entire outdoor exhaust and venting about every 18 months.
What does EF1 mean on an Electrolux dryer?
The owner guide calls it a ventilation blockage. Check the lint filter, the exhaust tube and the vent exit, and clear debris. It is described as a known installation issue.
Why did my dryer quit partway through drying?
An overload can overheat the motor. Wait half an hour, then dry a smaller load. A tripped thermal limiter needs a technician.
Codes, symptoms, parts and service
Link the message to what to do next.
E65
E65 means the high limit thermostat has tripped too many times, per Electrolux's dryer chart. The chart lists a restricted vent first, then the thermostat or, on electric models, the inlet thermal limiter. Clean the lint screen and vent, then book a technician.
Electrolux dryer noisy, rattling or shaking
Most dryer noise has a simple source: coins or buckles in the drum, a loose pedestal, shipping bolts still in place or a dryer that is out of level. Electrolux also lists sounds that are normal, such as the chime at the end of a cycle.
Dryer thermal limiter
The thermal limiter is a temperature safety part in the dryer’s heated air path. When it opens, the circuit stops. Electrolux’s dryer sheet names the outlet limiter (plus an inlet limiter on gas models) behind E66, and an inlet limiter on electric models behind E65.
Dryer repair
Book a diagnostic for your model at the appliance.
Find your metro
Office details and the access information to pass on.