What it means
E64 is an open circuit in the heater on Electrolux's dryer chart: the heating element or its wiring is defective. The dryer may tumble with no heat. Check the cycle and the breakers, then book a technician.
Electrolux dryer E64 / Heating
E64 is an open circuit in the heater on Electrolux's dryer chart: the heating element or its wiring is defective. The dryer may tumble with no heat. Check the cycle and the breakers, then book a technician.
Also shown as E64
E64 is an open circuit in the heater on Electrolux's dryer chart: the heating element or its wiring is defective. The dryer may tumble with no heat. Check the cycle and the breakers, then book a technician.
If the drum turns but the air is cold, that fits an open heater circuit.
The dryer turns without heat after the breakers and cycle are checked.
Your checklist, kept on this device

If the drum turns but the air is cold, that fits an open heater circuit.

Electrolux says Air Fluff or a no-heat temperature tumbles without warmth.

An electric dryer has two house circuits or fuses. If one is tripped, the heater will not run. [2]

The heater coils and terminals are line voltage parts.

The chart checks the heater coils and connections for open circuits and replaces the heater and/or wiring.
Send us the model and the checks you have done, and open your request here.
Book a visit

A simplified drawing, since layouts differ between models. Pick an outlined part for its photo and the related check.

Component reference
The heating element is the set of heater coils that warm the air in an Electrolux dryer.
Read the definitionThere is a break in the heater's electrical path. The chart's condition reads heating element or wiring defective.
Read the supporting manualThe cycle selection and the two house breakers. Both are on Electrolux's no-heat checklist.
Read the supporting manualCheck the heater coils and connections for open circuits, then replace the heater and/or wiring and retest.
Read the supporting manualAn open circuit is not a hazard by itself, but the dryer will not dry properly. Use a timed cycle only if clothes get dry.
Read the supporting manualManufacturer document
Electrolux (technician sheet; retailer-hosted copy)
P/N 137265000B (1202); Canadian SKU EIMED6CJIW; original file dated 2009 / sheet p.1 (Error Code Chart)
Manufacturer document
Electrolux / Owner Center knowledge base (owner.electrolux.com)
Owner Center article, cached 10.11.2026 (no edition date printed) / article text
Row E64 of the dryer chart and Electrolux's no-heat article (KB 1853007).
E64 is one answer; tripped breakers and Air Fluff are others. Check those first.
No. E63 is a short to ground; E64 is a break in the circuit.
No. The chart lists only the heating element and its wiring for E64. A blocked vent shows up as EF1 or E65 instead.
For E64, the model number, whether it is gas or electric, and whether the drum warmed at all during the last cycle.
Codes, symptoms, parts and service
E63 is a heater to earth ground failure on Electrolux's dryer chart: the heating element or its wiring is shorted to the cabinet. Unplug the dryer and do not run it again until a technician has checked the heater.
Most dryer noise has a simple source: coins or buckles in the drum, a loose pedestal, shipping bolts still in place or a dryer that is out of level. Electrolux also lists sounds that are normal, such as the chime at the end of a cycle.
The heating element is the set of heater coils that warm the air in an Electrolux dryer. Electrolux's dryer chart names the element or its wiring for E63 (heater to earth ground) and E64 (heater open circuit). If the drum turns but the air stays cold, check the cycle and both house breakers first.
Book a diagnostic for your model at the appliance.
Office details and the access information to pass on.