Start from the symptom
Electrolux dryer will not start.
A dryer that will not start is usually waiting for a simple condition: the start control held long enough, the door fully shut, power at the plug, or a breaker that is still on. Electrolux also says a hot motor must rest for 30 minutes.

Start with safe observations.
Power the appliance down and pull the plug before any owner check. Beware of standing water and sharp debris. Never touch a wet plug or electrical area, take off service panels, or step beyond your model’s owner guide.
- 1
Hold the start control
Press or twist the start control and keep it held for two seconds so it registers, Electrolux says.
- 2
Nudge the cycle knob
If the selector sits a hair short of the start position, give it a small extra turn into the cycle so the pointer is clearly in place.
- 3
Close the door completely
The door must be fully closed for the dryer to run. Look for a sleeve or a sock caught at the edge.
- 4
Plug and outlet
Check that the plug fits snugly in the wall outlet. Electrolux warns against extension cords.
- 5
Breaker or fuse
A blown house fuse or a breaker that has tripped will stop the dryer. Restore the breaker or change the fuse for one of the same size, never a larger one. For an overloaded circuit, call a qualified electrician.
- 6
If it stopped by itself
Overloading can overheat the motor. Let it rest half an hour and use a smaller load. On electric dryers a thermal limiter can also switch the motor off, which needs a technician.
- 7
Codes E42 and E52
KB 1820071 shows E 42 as Door Open and asks you to check that the door is not blocked. The dryer sheet calls E42 a door sensing failure. E52 means the motor stopped or did not start.
Systems a technician may investigate.
The parts below tie in with this symptom. Seeing it does not prove any one of them has failed.
If the display adds a code.
Door
E42 appears in two Electrolux documents with two readings. The Owner Center guide shows E 42 as Door Open; the technician chart says door sensing failure with a defective control board. Close the door and clear the doorway; if E42 stays, book a visit.
Motor
E52 means the dryer motor stopped or will not start, per Electrolux's dryer chart. The listed conditions are an overheated motor, a load that is too heavy, low supply voltage, or a defective motor or wiring. Take the load out and let it cool.
Read the related care guide.

A code on the dryer? Recall it, then read its group.
To see the last code on an Electrolux dryer, wake it with any button except cancel, then hold cancel and start/pause for 6 seconds. Codes sort by their first digit into contact sensor, motor, heat, thermistor, board, supply and airflow groups, and most groups need a technician.

E61, E64, E65 or E66? Each one tests something different.
On an Electrolux dryer, E61 is the heater relay, E63 a heater short to ground, E64 an open heater circuit, E65 a high-limit thermostat that tripped too often and E66 an open thermal limiter. Only E65 sends the technician to the vent, and every one of them needs a visit.
When observation becomes a service request.
Leave internal testing to a technician.
When the dryer is still dead after these checks, or E42 or E52 returns with the door closed and a small load, book a visit. Say what happens when you press start: nothing, a hum, or a click.
Arrange a diagnosticSources and model boundaries.
These sources back the Electrolux dryer will not start guidance. Use the manual for your own model.
- What should I do if my dryer does not start? (KB 1853009)
- What should I do if my dryer stops operating? (KB 1853011)
- Laundry Dryer Error Code Guide (KB 1820071)
- Dryer Tech Data Sheet, P/N 137265000B (1202)
Follow the guide for your exact model. Consult how we research these pages.
Why does my dryer do nothing when I press start?
Start with the basics: hold the button two seconds, close the door fully, check the plug and look at the breaker and the fuses. Electrolux lists each of these.
Can an extension cord stop the dryer?
Electrolux says not to use an extension cord with the dryer. Plug it straight into the wall outlet and make sure the plug is snug.
The dryer quit mid-cycle and will not restart. Why?
The motor may be overheated from a large load. Give it half an hour and dry smaller loads. If it still does not run, a thermal limiter may have tripped.
Do E42 and E52 mean the same thing?
No. E42 concerns the door. Electrolux's guide says Door Open, while the sheet says door sensing failure. E52 is a motor that stopped or would not start.
Codes, symptoms, parts and service
Link the message to what to do next.
E42
E42 appears in two Electrolux documents with two readings. The Owner Center guide shows E 42 as Door Open; the technician chart says door sensing failure with a defective control board. Close the door and clear the doorway; if E42 stays, book a visit.
Electrolux dryer noisy, rattling or shaking
Most dryer noise has a simple source: coins or buckles in the drum, a loose pedestal, shipping bolts still in place or a dryer that is out of level. Electrolux also lists sounds that are normal, such as the chime at the end of a cycle.
Dryer thermal limiter
The thermal limiter is a temperature safety part in the dryer’s heated air path. When it opens, the circuit stops. Electrolux’s dryer sheet names the outlet limiter (plus an inlet limiter on gas models) behind E66, and an inlet limiter on electric models behind E65.
Dryer repair
Book a diagnostic for your model at the appliance.
Find your metro
Office details and the access information to pass on.
