Troubleshooting

Electrolux washer will not start: LOC, door codes E41 and E42, and the start checklist

Check the display. LOC is the control lock: scroll to the control lock option and press Select. E41 means the door switch reads open; E42 means the door lock is not recognized. For both, remove anything keeping the door open and listen for the click. Then check Start, Delay Start and power.

Hand pressing a front-load washer door shut by the handle, with a basket of laundry on the floor.
Experienced techniciansWarranty on our workmanshipOEM parts available on orderUpfront pricing, agreed before work
On this page
Key points
  • LOC: scroll to the control lock option and press Select to turn it off. 1
  • E41: the control board thinks the door switch is open. 2
  • E42: the door lock is not being recognized. 3
  • The washer powers off after 10 minutes without Start. 4
  • The sheet shows 41 to the user and lists 42 as not shown. 5

Why won't my Electrolux washer start?#

Start with the display. LOC means the control lock is on. E41 means the control board thinks the door switch is open. E42 means the door lock is not being recognized. With none of those, the Owner Center's general list covers Start, Delay Start, power and the breaker. 1234

Each cause has its own short fix, and the first three are on the washer itself. Work down the table and stop when the washer runs.

SignWhat Electrolux saysWhere to look
LOC, or a lock iconControl lock is on; cycles will not runControl lock option 1
E41Control board thinks the door switch is openDoor, latch, striker 2
E42Door lock is not being recognizedDoor, latch, striker 3
Nothing happensStart not pressed, Delay Start set, plug loose, breaker trippedGeneral checklist 4

What clears the LOC message?#

Scroll to the control lock option and press Select. The control lock icon goes out on the LED display, and cycles can run again. The lock exists to lock the controls between cycles and cut the chance of accidental operation by children. 1

The steps to turn it on are the same two: scroll to the option, press Select, and the icon appears. If the washer seems dead after someone cleaned the panel or a child pressed buttons, this is the first place to look. 1

  1. 1

    Look at the display for the lock icon#

    A lit control lock icon or LOC means the lock is on. 1

    Close view of a washer control panel with a black display showing a lit padlock icon next to a round knob.
  2. 2

    Scroll to the control lock option#

    Use the same scroll control you use to pick cycles. 1

  3. 3

    Press Select#

    The icon goes out and the controls respond again. 1

  4. 4

    Choose a cycle and press Start#

    Cycles do not run while the lock is active, so test with a short one. 1

What do E41 and E42 mean?#

E41: the control board thinks the door switch is open. E42: the door lock is not being recognized. Electrolux gives the same four checks for both: is the door completely closed, is anything keeping it from closing, do you hear a click when it shuts, and are the latch and striker working. 23

On the technician sheet the two are not treated alike. 41 reads "control board thinks the door switch is open" and is marked as shown to the user. 42 reads "door lock device failure" and is marked not shown, though the Owner Center article treats it as a code owners see. 5

You can read the single pages for E41 and the washer code hub for E42.

What the door checks look like in practice#

Open the door and look at the opening and the seal for clothes, debris or a sleeve caught at the edge. Close the door with one firm push and listen for the click. If the door shuts with no click, or you see a bent or damaged latch or striker, stop there. 23

Open front-load washer door showing the latch hook on the door and the catch plate on the frame.
The latch on the door and the catch on the frame must meet for the lock to register.

The washer door lock is the part the E42 message talks about, and the glossary page shows where it sits.

What else stops a washer from starting?#

The Owner Center's checklist is short. Press Start after your selections; the washer shuts off after 10 minutes without it. Check Delay Start. Confirm the plug is tight, with no extension cord. Turn the water valves on. Reset a tripped breaker. 4

Details from that article, in the order it gives them:

  • Level. Ensure the washer is level. 4
  • Delay Start. Make sure you did not set it by accident. The wash may simply be in a pause. 4
  • Pause between steps. A pause occurs between wash and spin, and a longer one during a soak cycle. This is normal. 4
  • The lid. The article says the washer will not operate if the lid is not closed properly. It is written with a lid in mind, so on a front-load model read that as the door. 4
  • Power. The plug must fit tightly in the outlet. An extension cord can reduce power to the washer. 4
  • Water. The water valves must be on and water available to the unit. 4
  • Fuse or breaker. Reset the breaker or replace the fuse, but do not increase the fuse capacity. 4
  • Overloaded circuit. Contact a qualified electrician. 4

What if it started and then stopped?#

Check the display for a code, then check the door again. The sheet also lists 44, door closed sensing failure, and 45, line door sensing failure. Both are marked not shown to the user, so a door problem can sit behind a washer that simply stops. 5

The sheet also lists F5, load unbalanced, as not shown to the user, with the next step to redistribute the load and restart. 5

When does a washer that will not start need a technician?#

Book when E41 or E42 returns with the door fully closed and the latch and striker undamaged, when the controls are unlocked and nothing happens on Start, or when the breaker trips again. A technician can test the door switch, the lock and the circuit. 234

Next step: \book a visit\, or look over our washer service. The technician agrees the price with you before any work starts. The exact cost is confirmed after the on-site diagnostic. If your unit is under the manufacturer's warranty, the manufacturer handles that repair. We give a warranty on our workmanship.

Sources#

  1. Laundry front loading washer displaying Error Code LOC ​control lock activator. (KB 1829278)Electrolux / Owner Center knowledge base (owner.electrolux.com) · Owner Center article, cached 10.11.2026 (no edition date printed) · article text
  2. Laundry front loading washer displaying Error Code E41 door is open. (KB 1820509)Electrolux / Owner Center knowledge base (owner.electrolux.com) · Owner Center article, cached 10.11.2026 (no edition date printed) · article text
  3. Laundry front loading washer displaying Error Code E42 door lock device failure. (KB 1829258)Electrolux / Owner Center knowledge base (owner.electrolux.com) · Owner Center article, cached 10.11.2026 (no edition date printed) · article text
  4. What should I do if my washer does not start? (KB 1853029)Electrolux / Owner Center knowledge base (owner.electrolux.com) · Owner Center article, cached 10.11.2026 (no edition date printed) · article text
  5. Washer Tech Data Sheet, A11200302 (1803)Electrolux (technician sheet; retailer-hosted copy) · A11200302 (1803); 2018, 300/400/500/600 series · p.3 (Washer Error Codes: 41 and 42, Display column)

Here to help

Good questions.
Clear answers.

Talk to our team
What does LOC mean on my Electrolux washer?

LOC means the control lock is on. It locks the controls between cycles to reduce accidental operation by children, and cycles will not run while it is active. [1]

How do I unlock the controls?

Scroll to the control lock option and press Select again. The control lock icon on the LED display goes out. The same two steps turn the lock on. [1]

What is the difference between E41 and E42?

E41 means the control board thinks the door switch is open. E42 means the door lock device is not being recognized. Both start with the same door and latch checks. [2][3]

Does the washer shut itself off if I wait?

Yes. Electrolux says that if the washer is left on more than 10 minutes without pressing Start, it turns off automatically and you must start your selections over. [4]

Is Delay Start a reason it seems stuck?

It can be. Electrolux says to make sure you did not set Delay Start by accident, because the wash cycle might be waiting. A pause between wash and spin is also normal. [4]

Let’s take care of it.

Premium appliances deserve
careful service.