Diagnostics and repair
Experienced technicians inspect the appliance before proposing any work. OEM parts can be ordered, with the right part matched to your model.
The care journal
What your display code is saying, how nearby codes differ and what to try first.

On an Electrolux dryer, E61 is the heater relay, E63 a heater short to ground, E64 an open heater circuit, E65 a high-limit thermostat that tripped too often and E66 an open thermal limiter. Only E65 sends the technician to the vent, and every one of them needs a visit.

On an Electrolux dryer, E91 means the control board and interface board are not communicating, E92 means they are not compatible and E93 means the machine configuration data failed its check. None is an owner repair, and the model number matters because the sheet's remedies depend on matching parts.

F14 appears only on the ES630 oven control and means a misconnected keyboard cable. F15 means a failed controller self check on the ES630 but a keyboard error on the 2017 modular control, so your model number decides which row applies. Switch the oven off for 30 seconds, then book a technician if it comes back.

An Electrolux front-load washer shows only some codes. To read the last stored one, power on, wait at least 10 seconds, then hold temp and select for 3 seconds. The display shows the last error in memory. Hidden codes include E13, E23, E31 and E62, and they need a technician.

Wake the dryer, hold cancel and start/pause together for 6 seconds and write down the E and two digits that appear.
Read the full sequence
Most dryer noise has a simple source: coins or buckles in the drum, a loose pedestal, shipping bolts still in place or a dryer that is out of level. Electrolux also lists sounds that are normal, such as the chime at the end of a cycle.

A drum that turns without heat often means one of the two house circuits feeding an electric dryer has tripped. Electrolux also lists the cycle choice, a 240-volt supply and, on gas models, the gas valve, the propane tank and the air around the dryer.

Overheating and over-drying nearly always come down to settings or airflow. Electrolux's advice is the right cycle, Auto Dry in place of Timed Dry, a clean lint screen and a clear exhaust. Its E65 and EF1 codes both start with a restricted vent.

The contact sensor reads how damp the load is. Electrolux’s dryer sheet labels its test row “MOIST. BARS” and ties E31 and E32 to a frequency reading that is too high or too low. A foreign object touching the sensor is one listed cause.

Control thermistors are the temperature sensors that tell the dryer how hot the air is. Electrolux’s sheet names an outlet, an inlet and an exhaust thermistor. E71 to E74 mean an open or shorted sensor circuit, and EF1 and EF3 list them among the causes.

A heater relay is the switch that sends power to the dryer’s heating element. Electrolux’s dryer sheet ties E61 to it: the relay stuck open or closed, or the wiring around it defective. A technician tests it with the cycle stopped.
E42 appears in two Electrolux documents with two readings. The Owner Center guide shows E 42 as Door Open; the technician chart says door sensing failure with a defective control board. Close the door and clear the doorway; if E42 stays, book a visit.
E53 is a motor centripetal switch failure on Electrolux's dryer chart. The switch inside the motor, the control board or the wiring is defective. Unplug the dryer and book a technician; the chart's fixes are wiring checks and parts.
E61 is a heater relay failure on Electrolux's dryer chart: a heater relay is stuck open or closed, or the wiring is defective. If the dryer runs without heat, or heats when it should not, unplug it and book a technician.
E65 means the high limit thermostat has tripped too many times, per Electrolux's dryer chart. The chart lists a restricted vent first, then the thermostat or, on electric models, the inlet thermal limiter. Clean the lint screen and vent, then book a technician.
E91 is a communication error between the dryer's control board and its interface board, per Electrolux's dryer chart. The cause is the wiring, the control board or the interface board. Restart once, then book a technician.
EF1 on an Electrolux dryer means the vent is blocked. The chart calls it vent blocked and the Owner Center guide calls it ventilation blockage, a known installation issue. Clean the lint filter, check the exhaust tube and the vent exit.
Experienced technicians inspect the appliance before proposing any work. OEM parts can be ordered, with the right part matched to your model.
An Electrolux still under its manufacturer warranty goes to Electrolux for covered repairs. Our repairs carry a warranty on our workmanship.
They may be aimed at different readers and dates, say a technician chart and an owner article. On dryer E42 the page quotes both and does not pick a winner.
We report what the documents do state, add the checks that are safe, and say when to book. Guessing at the meaning is something we refuse to do.
No. They name causes for people who open the machine. We mark such lines as technician notes and offer owners only the steps Electrolux publishes for them.
Photograph it first. A reset can erase a message that appears once, but the picture still helps a technician if that code was an early warning.
Codes, symptoms, parts and service
A washer that will not spin is most often reacting to an unbalanced or heavy load, a machine that is out of level, or a door that is not locked. Electrolux's sheet ties the motor-speed codes E55 and E59 to the motor, belt, tub bearings and motor control board.
Book a diagnostic for your model at the appliance.
Office details and the access information to pass on.