Start from the symptom
Electrolux dishwasher lights flashing or showing a code.
Flashing lights and display codes on an Electrolux dishwasher are not always a breakdown. A delay countdown (01-24) and a heat delay (Hd or HO) are normal waiting states, while i20 and i40 point to draining and a clogged filter or sump.

Start with safe observations.
Power the appliance down and pull the plug before any owner check. Beware of standing water and sharp debris. Never touch a wet plug or electrical area, take off service panels, or step beyond your model’s owner guide.
- 1
Delayed start
Code 01-24 means the delay option is on and the cycle begins when the displayed time reaches 0. To cancel, press or hold Cancel. A second press cancels the selected cycle and starts a drain routine, and a third ends the drain and shuts the unit off.
- 2
Heat delay
Hd or HO means the dishwasher is in Heat Delay or Heater On mode, waiting for the water to heat. The colder the water, the longer the wait: roughly 1 to 2 minutes per degree of temperature rise.
- 3
Drain problem
i20 means the dishwasher did not drain properly. Electrolux asks you to check that the disposer knockout plug is removed, that the drain hose is not blocked, pinched or restricted, that the hose is at least 32 inches above the floor and that the filter is clear of food.
- 4
Clogged filter
i40 points to a clogged filter or sump where food residue has piled up. Clean out the glass trap and run the cycle again.
- 5
Reset
For i20, Electrolux lists holding Cancel, turning the power off at the breaker or unplugging the dishwasher for 3 minutes.
- 6
Read the alarms video
Electrolux's article How to Use Your Dishwasher: Alarms & Codes is a video, so the written pages above cover only these four.
Systems a technician may investigate.
The parts below tie in with this symptom. Seeing it does not prove any one of them has failed.

Glass trap and filter
The glass trap and filter collect food soil before the drain. Electrolux ties both i20 and i40 to them: i40 is printed as a clogged filter or sump, caused by food residue that has collected, and i20 lists the glass trap among the things to clear.

Dishwasher drain hose
The drain hose carries wastewater away from the tub. When Electrolux shows i20, the unit did not drain properly, and the hose is the second item on its list: free of blockage and pinching and at a height of 32 inches or more.
If the display adds a code.
No code is tied directly to this topic.
No further researched dishwasher code is tied to this topic. Match the exact message to your model manual and do not swap in another code from the library.
See the research statusWhen observation becomes a service request.
Leave internal testing to a technician.
Book a visit if a code returns after cleaning the filter and checking the drain hose, or if the lights flash with no cycle running. Tell us the code shown. We do not list every dishwasher code here.
Arrange a diagnosticSources and model boundaries.
These sources back the Electrolux dishwasher lights flashing or showing a code guidance. Use the manual for your own model.
- Dishwasher Error Code 01-24 - Delayed option has been activated (KB 1830334)
- Dishwasher Error Code Hd or HO - Heat delay or heater on mode activated (KB 1830362)
- Dishwasher Error Code i20 - Unit did not drain properly (KB 1830367)
- Dishwasher Error Code i40 - Clogged filter or sump (KB 1831281)
- How to Use Your Dishwasher: Alarms & Codes (KB 1853201)
Follow the guide for your exact model. Consult how we research these pages.
What does 01-24 mean?
The delay option is on. The cycle will begin when the displayed time reaches 0. Press Cancel to stop the delay.
Is Hd or HO a problem?
No. It means the dishwasher is waiting to heat the water. Colder water means a longer wait, about 1 to 2 minutes per degree it must rise.
What do i20 and i40 mean?
i20 is a drain problem. i40 is a filter or sump blocked by food residue. Check the hose and clean the glass trap first.
How do I reset an Electrolux dishwasher code?
For i20, Electrolux lists holding Cancel, turning the breaker off or unplugging the unit for 3 minutes.
Codes, symptoms, parts and service
Link the message to what to do next.
Electrolux dishwasher lights flashing or showing a code
Flashing lights and display codes on an Electrolux dishwasher are not always a breakdown. A delay countdown (01-24) and a heat delay (Hd or HO) are normal waiting states, while i20 and i40 point to draining and a clogged filter or sump.
Dishwasher drain hose
The drain hose carries wastewater away from the tub. When Electrolux shows i20, the unit did not drain properly, and the hose is the second item on its list: free of blockage and pinching and at a height of 32 inches or more.
Dishwasher repair
Book a diagnostic for your model at the appliance.
Find your metro
Office details and the access information to pass on.