Before work starts
The technician examines the appliance, tells you what the repair involves and agrees the cost with you before opening anything up.
Independent appliance repair
We repair Electrolux dishwashers that won’t start, don’t drain, leave water behind or show a code. Tell us the code and when it appears, then book a technician.


Flashing lights and display codes on an Electrolux dishwasher are not always a breakdown. A delay countdown (01-24) and a heat delay (Hd or HO) are normal waiting states, while i20 and i40 point to draining and a clogged filter or sump.

A dishwasher that seems idle may be waiting. A delayed start (01-24) holds the cycle until the countdown reaches 0, and a heat delay (Hd or HO) pauses while the water warms. Check these before looking for a failure.

Water left in the tub points first at the hose, the disposer connection and the filter. Electrolux's i20 article lists the knockout plug, hose blockage or pinching, hose height and the glass trap, and i40 adds a clogged filter or sump.

Electrolux's written dishwasher articles do not describe a control lock, so this page is short. What they do show is that a dishwasher can look unresponsive while it counts down a delayed start or waits for the water to heat, and that Cancel and a power reset are the documented ways out.
No further researched dishwasher code is tied to this topic. Match the exact message to your model manual and do not swap in another code from the library.
See the research statusNo parts are linked here because the Electrolux documents we hold do not name them for this appliance. We name a part only after the diagnostic visit, checked against your model number.

This component has no illustrated glossary entry here. Rely on the system named in the explanation and the cited model manual; a code alone does not name a replacement.
Explore the researched partsHow a repair visit runs.
Measured and clear.

Name the washer, dryer or oven and say what it does. Add the code on the screen if there is one.

The technician runs the cycle, checks the parts behind the code and explains the cost before starting.

The part is replaced, a test cycle confirms the fix, and the technician walks you through the result.
Electrolux’s articles name i20 (did not drain), i40 (clogged filter or sump), 01 to 24 (a delayed start) and Hd or HO (heat delay).
For a 01 to 24 display, press or hold Cancel. A second press cancels the cycle and starts a drain routine; a third turns the unit off.
Hd or HO means the dishwasher is heating the water. Electrolux says colder water makes it longer, roughly 1 to 2 minutes for each degree of rise.
For i20, check that the disposer’s knockout plug is out, the hose is not blocked or pinched, and it runs at least 32 inches above the floor.
Both i20 and i40 articles name food soil in the glass trap or filter as a cause. Clean it and run the unit again.
i20 or i40 coming back after a clean drain path and filter is the cue to book a technician.
Book a technician if the dishwasher still won’t start after you cancel a delay and check the door.
If water pools on the floor beside the machine, turn its breaker off first.
Pump and wiring work belongs to the technician.
Arrange a diagnosticThe technician examines the appliance, tells you what the repair involves and agrees the cost with you before opening anything up.
An Electrolux still under its manufacturer warranty goes to Electrolux for covered repairs. Our repairs carry a warranty on our workmanship.
It means the dishwasher did not drain properly. Look at the disposer plug, the drain hose and the glass trap. If the code comes back, book a technician.
A delayed start, shown as 01 to 24, is one cause; press Cancel to clear it. A displayed Hd or HO is a normal heat delay. Work through those and the door; a machine that still will not run needs a visit.
Electrolux lists three ways: hold Cancel, cut power at the breaker, or leave the unit unplugged for 3 minutes. If the error comes back, book a technician.
Yes, tell us the model when you book. We focus on drain, start and leak problems, and a technician diagnoses anything else on site.
If your unit is under the manufacturer’s warranty, the manufacturer handles that repair.
Codes, symptoms, parts and service
Flashing lights and display codes on an Electrolux dishwasher are not always a breakdown. A delay countdown (01-24) and a heat delay (Hd or HO) are normal waiting states, while i20 and i40 point to draining and a clogged filter or sump.
Book a diagnostic for your model at the appliance.
Office details and the access information to pass on.