Start from the symptom
Electrolux dishwasher not draining.
Water left in the tub points first at the hose, the disposer connection and the filter. Electrolux's i20 article lists the knockout plug, hose blockage or pinching, hose height and the glass trap, and i40 adds a clogged filter or sump.

Start with safe observations.
Power the appliance down and pull the plug before any owner check. Beware of standing water and sharp debris. Never touch a wet plug or electrical area, take off service panels, or step beyond your model’s owner guide.
- 1
Disposer knockout plug
If the dishwasher connects to a disposer, make sure the knockout plug has been removed.
- 2
Hose blockage
Check that the drain hose is not blocked, obstructed, pinched or restricted.
- 3
Hose height
The hose should be at least 32 inches from the floor at its high point.
- 4
Glass trap and filter
Make sure the glass trap and filter are free of food soil. For i40, clean out the glass trap and run the dishwasher again.
- 5
Reset the code
Hold Cancel, turn the power off at the breaker or unplug the dishwasher for 3 minutes.
Systems a technician may investigate.
The parts below tie in with this symptom. Seeing it does not prove any one of them has failed.

Disposer knockout plug
The knockout plug is a blank that seals the garbage disposer inlet until it is removed, which has to happen when the dishwasher drains through a disposer. Electrolux lists it first when the dishwasher shows i20 (unit did not drain properly).

Dishwasher drain hose
The drain hose carries wastewater away from the tub. When Electrolux shows i20, the unit did not drain properly, and the hose is the second item on its list: free of blockage and pinching and at a height of 32 inches or more.

Glass trap and filter
The glass trap and filter collect food soil before the drain. Electrolux ties both i20 and i40 to them: i40 is printed as a clogged filter or sump, caused by food residue that has collected, and i20 lists the glass trap among the things to clear.
If the display adds a code.
No code is tied directly to this topic.
No further researched dishwasher code is tied to this topic. Match the exact message to your model manual and do not swap in another code from the library.
See the research statusWhen observation becomes a service request.
Leave internal testing to a technician.
Book a visit if water remains after the hose, plug and filter checks, or if i20 or i40 returns. Tell us the code and whether a disposer is connected.
Arrange a diagnosticSources and model boundaries.
These sources back the Electrolux dishwasher not draining guidance. Use the manual for your own model.
- Dishwasher Error Code i20 - Unit did not drain properly (KB 1830367)
- Dishwasher Error Code i40 - Clogged filter or sump (KB 1831281)
Follow the guide for your exact model. Consult how we research these pages.
What does i20 mean?
The dishwasher did not drain properly. Electrolux asks you to check the disposer plug, the hose and its height, and the filter.
What does i40 mean?
A clogged filter or sump from food soil. Clean the glass trap and rerun the dishwasher.
What is the minimum drain hose height?
32 inches from the floor, according to Electrolux's i20 article.
How do I clear the code?
Hold Cancel, turn off the breaker or unplug the dishwasher for 3 minutes.
Codes, symptoms, parts and service
Link the message to what to do next.
Electrolux dishwasher lights flashing or showing a code
Flashing lights and display codes on an Electrolux dishwasher are not always a breakdown. A delay countdown (01-24) and a heat delay (Hd or HO) are normal waiting states, while i20 and i40 point to draining and a clogged filter or sump.
Dishwasher drain hose
The drain hose carries wastewater away from the tub. When Electrolux shows i20, the unit did not drain properly, and the hose is the second item on its list: free of blockage and pinching and at a height of 32 inches or more.
Dishwasher repair
Book a diagnostic for your model at the appliance.
Find your metro
Office details and the access information to pass on.