Start from the symptom
Electrolux range surface burner not heating.
For a surface element that stays cold, the check depends on the cooktop type. On coil burners, test the safety switch and move the coil to another receptacle. On glass, cut the range's power for 30 seconds. On induction, use cookware a magnet sticks to.

Start with safe observations.
Power the appliance down and pull the plug before any owner check. Beware of standing water and sharp debris. Never touch a wet plug or electrical area, take off service panels, or step beyond your model’s owner guide.
- 1
Name your cooktop type
Coil, smooth glass and induction each have their own checks. The steps below follow Electrolux's article for each.
- 2
Coils: test the center switch
Press the coil's center safety switch. It should rise again. If it does, take the coil out and inspect it for damage.
- 3
Coils: try another burner
Seat the coil again and retest the switch. Then try the coil elsewhere; where it heats shows if the coil itself or the receptacle has the problem.
- 4
Glass: reset the range
Disconnect the range for a short while and reconnect it. A newly installed range with every burner cold could have a voltage or wiring problem.
- 5
Induction: try a magnet
Hold a magnet to the bottom of the pan. Electrolux says if it sticks, the base material is right for induction.
- 6
Read the indicator lights
The element-on light shows when a control is on. The hot-surface light stays on until the glass has cooled to a moderate level.
More about this symptom.
What should I check first on a cold coil burner?#
Push the safety switch at the center of the coil and watch it rise. Next lift the coil out, inspect it, seat it and retest. Electrolux also suggests trying it in another burner.
What resets a smooth glass cooktop?#
Disconnect and reconnect the range after 30 seconds. Electrolux starts there when a glass cooktop will not heat, and a newly installed range with no heat at all may have a wiring problem.
Why test an induction pan with a magnet?#
Induction needs a base the magnet grips. Electrolux says heavy gauge cookware gives the best results, and cast iron and magnetic stainless steel are suitable. Do not slide cast iron on the glass.
Systems a technician may investigate.
The parts below tie in with this symptom. Seeing it does not prove any one of them has failed.

Induction cooking zone
An induction cooking zone heats the pan itself, so the cookware has to be right. Electrolux says to use quality heavy-gauge cookware and hold a magnet to the underside of the pan. If it clings, the material suits induction.

Surface indicator lights
An Electrolux range can carry two surface lights. Element on glows while any surface control is on. Hot surface outlasts the cooking and stays lit until the glass is only warm, which the article calls a moderate level. Neither is an error signal.
If the display adds a code.
No code is tied directly to this topic.
No further researched dishwasher code is tied to this topic. Match the exact message to your model manual and do not swap in another code from the library.
See the research statusRely on the care guidance written for this appliance.
When observation becomes a service request.
Leave internal testing to a technician.
A coil or glass element is still cold after these checks.
No surface element heats on a newly installed range.
The coil or its receptacle shows damage.
The element-on light is lit but the pan stays cold.
Arrange a diagnosticSources and model boundaries.
These sources back the Electrolux range surface burner not heating guidance. Use the manual for your own model.
- Ranges - No Heating (KB 1819544)
- Ranges - What do the indicator lights on my range mean? (KB 1847370)
- Ranges - What type of cookware do I use with Induction? (KB 1847372)
Follow the guide for your exact model. Consult how we research these pages.
How do I tell a bad coil from a bad receptacle?
Put the coil in a different burner. If it heats there, the coil is good and the first receptacle is suspect. If it stays cold, the coil has failed. Electrolux uses this swap to separate the two.
Why will my induction zone not heat a pan?
The pan base may not suit induction. Electrolux says to test with a magnet: if it sticks to the bottom, the material is right. Not all stainless steel is magnetic, so test each pan.
What do the two indicator lights mean?
The element-on light comes on when a surface element is turned on. The hot-surface light comes on when a cooking area heats and stays lit until the glass cools to a moderate level.
Can cookware change how well the range heats?
Yes. Electrolux says cookware plays a major role. Use flat-bottomed pots and pans that are medium to heavy so heat spreads evenly and food does not burn or cook unevenly.
My new range has no heat on any burner. Why?
A glass cooktop on a recently installed range that stays cold after the power reset could have a supply problem. Leave the range closed and book a technician.
Codes, symptoms, parts and service
Link the message to what to do next.
Electrolux range surface burner not heating
For a surface element that stays cold, the check depends on the cooktop type. On coil burners, test the safety switch and move the coil to another receptacle. On glass, cut the range's power for 30 seconds. On induction, use cookware a magnet sticks to.
Induction cooking zone
An induction cooking zone heats the pan itself, so the cookware has to be right. Electrolux says to use quality heavy-gauge cookware and hold a magnet to the underside of the pan. If it clings, the material suits induction.
Range repair
Book a diagnostic for your model at the appliance.
Find your metro
Office details and the access information to pass on.