Before work starts
The technician examines the appliance, tells you what the repair involves and agrees the cost with you before opening anything up.
Independent appliance repair
We repair Electrolux freestanding ranges, gas, electric, dual fuel and induction: burners that will not ignite, smoothtop zones that behave oddly, an induction zone that ignores a pan, a locked cooktop or a code on the display. Give us the fuel type and model, then book a technician.


For a surface element that stays cold, the check depends on the cooktop type. On coil burners, test the safety switch and move the coil to another receptacle. On glass, cut the range's power for 30 seconds. On induction, use cookware a magnet sticks to.

If the range door refuses to open, or F90 to F94 shows, Electrolux wants power off for up to half a minute, using the plug or the breaker. First rule out the Lock feature, which also secures the door.
Only parts Electrolux's own sheets tie to range failures are listed. The technician confirms each against your model number after the diagnostic, and you approve any replacement before it is fitted.

The door lock motor turns the latch that holds the oven door shut during self-clean. Electrolux’s sheets use F90 for a failure of that mechanism, and the modular sheet adds F95 and F97. The owner guide groups F90 to F94 as a door lock issue.

The touch panel is joined to the display board by two ribbon cables. Electrolux’s ES630 sheet uses F14 for a misconnected keyboard cable there. The 2017 modular sheets print no F14 and use F01 to F05, F28 and F29 for touch panel problems.
How a repair visit runs.
Measured and clear.

Name the washer, dryer or oven and say what it does. Add the code on the screen if there is one.

The technician runs the cycle, checks the parts behind the code and explains the cost before starting.

The part is replaced, a test cycle confirms the fix, and the technician walks you through the result.
A dash means the cooktop is locked. Hold OFF for 6 seconds to cancel the lock. Setting the oven lock uses the same press, and the door takes about 15 seconds to latch.
Soften spills with hot soapy water, then clear the burner head slots and the ignition ports with a soft brush, toothpick or paperclip. No abrasive cleaners, oven cleaner or steel wool.
Each burner cap has to sit firmly and level on its head. The surface knob must be at the lite position. Food debris in the ports can hold back gas flow.
Radiant elements switch on and off even at High. Expect more cycling when the pan is smaller than the element or its base is not fully flat.
If a magnet clings to the base, the metal suits induction. Not every stainless steel is magnetic. Cast iron works but must not slide, and rough bases scratch the glass.
For F1, F40/F41 or F90 to F94, disconnect power for up to 30 seconds, by unplugging or flipping the breaker off and on. On a dual fuel range, F20 is a link failure between the oven controller and the surface element controller.
A burner will not light with clean ports, seated caps and the knob at lite.
A lockout code returns after the 30-second power reset.
F20 appears on a dual fuel range, or the surface display shows nothing at all.
An induction zone stays off under a pan that a magnet clings to.
Gas fittings and wiring are for the technician. If you smell gas, leave first and ring your gas supplier.
Arrange a diagnosticThe technician examines the appliance, tells you what the repair involves and agrees the cost with you before opening anything up.
An Electrolux still under its manufacturer warranty goes to Electrolux for covered repairs. Our repairs carry a warranty on our workmanship.
Freestanding ranges with a cooktop on top. Wall ovens and the ovens inside ranges are covered on the ranges and ovens page, so say which you have.
Electrolux's code guide says a dash means the cooktop is locked. Hold OFF for 6 seconds to cancel it. If the dash returns by itself, book a technician.
Not by itself. Radiant elements cycle on and off even on High, more so with a small or uneven pan. A zone that stays cold is the sign to book us.
Heavy, flat pans with a magnetic base. A magnet that sticks to the bottom confirms it. Some stainless steel is not magnetic, so test rather than assume.
If the range is within the manufacturer's warranty, the manufacturer handles that repair. After that, or if you prefer an independent technician, book us and approve the price first.
Codes, symptoms, parts and service
F20 means the oven controller has found a problem with the link to the surface element controller (ESEC). It appears on the dual-fuel range sheet. Check whether the surface element displays light; if not, the controller has no power. Then book a technician.
For a surface element that stays cold, the check depends on the cooktop type. On coil burners, test the safety switch and move the coil to another receptacle. On glass, cut the range's power for 30 seconds. On induction, use cookware a magnet sticks to.
The door lock motor turns the latch that holds the oven door shut during self-clean. Electrolux’s sheets use F90 for a failure of that mechanism, and the modular sheet adds F95 and F97. The owner guide groups F90 to F94 as a door lock issue.
Book a diagnostic for your model at the appliance.
Office details and the access information to pass on.