What it means
H2 or B2 is a power supply issue in Electrolux's Owner Center dryer guide, which says to contact the electric company. Stop using the dryer, check the plug, outlet and breakers, and book a visit if the supply is normal.
Electrolux dryer H2 / B2 / Power supply
H2 or B2 is a power supply issue in Electrolux's Owner Center dryer guide, which says to contact the electric company. Stop using the dryer, check the plug, outlet and breakers, and book a visit if the supply is normal.
Also shown as H2 / B2
H2 or B2 is a power supply issue in Electrolux's Owner Center dryer guide, which says to contact the electric company. Stop using the dryer, check the plug, outlet and breakers, and book a visit if the supply is normal.
A supply the control rejects can damage it.
H2 or B2 returns after the breakers are reset and the utility finds the supply normal.
Your checklist, kept on this device

A supply the control rejects can damage it. Leave it unplugged while you check.

An electric dryer uses two house circuits or fuses. Reset a tripped one, as Electrolux's no-heat article says, and never replace a fuse with a larger one. [2]

The plug should fit tightly. Do not use an extension cord; Electrolux says it can greatly reduce the power. [3]

The guide's step for H2/B2 is to contact the electric company. Say the dryer reports a power supply issue.

If the supply measures normal, we look at the dryer's control and wiring. Tell us the model and the characters shown.
Send us the model and the checks you have done, and open your request here.
Book a visit


A simplified drawing, since layouts differ between models. Pick an outlined part for its photo and the related check.
A power supply issue. Electrolux's dryer guide lists it that way and sends you to the electric company.
Read the supporting manualThe guide points at the supply first. A dryer needs the right voltage on both legs, so a tripped breaker or a weak supply can produce it.
Read the supporting manualThe Electrolux washer sheet describes H2/B2 as supply voltage too high. The dryer guide gives no voltage detail, so we do not assume the same reading here.
Read the supporting manualNot until the supply is understood.
Read the supporting manualManufacturer document
Electrolux / Owner Center knowledge base (owner.electrolux.com)
Owner Center article, cached 10.11.2026 (no edition date printed) / article text
Manufacturer document
Electrolux / Owner Center knowledge base (owner.electrolux.com)
Owner Center article, cached 10.11.2026 (no edition date printed) / article text
Manufacturer document
Electrolux / Owner Center knowledge base (owner.electrolux.com)
Owner Center article, cached 10.11.2026 (no edition date printed) / article text
Electrolux's Owner Center dryer guide (KB 1820071), written for dryers in general. Cross-checks use the no-heat and no-start articles.
The guide says to. If the utility finds the supply normal, book a visit with us.
Possibly. Check both house breakers or fuses, as Electrolux's no-heat article suggests for a dryer that turns without heating. [2]
No. H4/B4 is incorrect wiring. They share a family of installation and supply issues.
For H2 / B2, the model number, the characters shown and what the electric company found.
Codes, symptoms, parts and service
H4 or B4 is incorrect wiring in Electrolux's Owner Center dryer guide, which calls it a known installation issue and points to the installer. Unplug the dryer, do not open the terminal block yourself, and ask the installer or book a visit.
Most dryer noise has a simple source: coins or buckles in the drum, a loose pedestal, shipping bolts still in place or a dryer that is out of level. Electrolux also lists sounds that are normal, such as the chime at the end of a cycle.
Book a diagnostic for your model at the appliance.
Office details and the access information to pass on.