What it means
F30 is an open oven temperature probe (RTD) or its wiring, on both Electrolux oven controls. Reset the power by unplugging for 30 seconds. The ES630 sheet adds that the control may show F10 first. If F30 returns, book a technician.
Electrolux oven F30 / Temperature probe
F30 is an open oven temperature probe (RTD) or its wiring, on both Electrolux oven controls. Reset the power by unplugging for 30 seconds. The ES630 sheet adds that the control may show F10 first. If F30 returns, book a technician.
Also shown as F30
F30 is an open oven temperature probe (RTD) or its wiring, on both Electrolux oven controls. Reset the power by unplugging for 30 seconds. The ES630 sheet adds that the control may show F10 first. If F30 returns, book a technician.
Unplug the oven for 30 seconds and plug it back in.
F30 returns after a 30-second reset.
Your checklist, kept on this device

Unplug the oven for 30 seconds and plug it back in. If you cannot unplug it, flip the breaker, which resets everything on that circuit. [6]

F30 appears when the oven is in an active mode or an attempt is made to start one. Let it cool and try a bake function.

The RTD probe sits inside the cavity wall. Leave it in place.

On the ES630 the control may show F10 and then F30, which points to the probe.
The sheets check the probe circuit wiring for an open, compare the RTD's resistance with the chart, replace the probe if it differs, then replace the relay board.
Send us the model and the checks you have done, and open your request here.
Book a visit
Component reference
The RTD is the oven’s temperature probe: a resistance temperature detector that tells the control how hot the cavity is.
Read the definitionThe oven's temperature probe circuit reads as open. The sheets word it open oven temperature sensor (RTD) and probe/wiring problem.
Read the supporting manualThe modular sheet's RTD table gives 1000 ohms at 32 F and 1091 ohms at 75 F, rising to 1453 ohms at 250 F. A reading off the chart means a new probe.
Read the supporting manualThe ES630 sheet notes the control may initially display F10 because it thinks a runaway condition exists, when the cause is an open probe.
Read the supporting manualNot if F30 returns. Without a probe reading the oven cannot regulate heat.
Read the supporting manualManufacturer document
Electrolux (technician sheet; retailer-hosted copy)
Models: EW30EW65PS
p/n 807436903 (Rev A 13/04) / PDF p.1 (EOC code descriptions)
Manufacturer document
Electrolux (technician sheet; retailer-hosted copy)
Models: EW30EW55PS
p/n 807436904 (Rev A 13/04) / PDF p.1
Manufacturer document
Electrolux (technician sheet; retailer-hosted copy)
Models: EW30DS80RS
p/n 807880710 EN (Rev A 16/02); 807880711 FR (Rev A 16/03) / PDF p.1
Manufacturer document
Electrolux (technician sheet; retailer-hosted copy)
Models: EI30EW38TS
p/n A00980644 Rev A (2017/05) / PDF p.1
Manufacturer document
Electrolux (technician sheet; retailer-hosted copy)
Models: EI30EW48TS
p/n A00980645 Rev A (2017/05) / PDF p.2 (code table)
Manufacturer document
Electrolux / Owner Center knowledge base (owner.electrolux.com)
Owner Center article, cached 10.11.2026 (no edition date printed) / article text
Row F30 of the ES630 sheets (807436903, 807436904, 807880710), the modular sheets (A00980644, A00980645) and the Oven Error Codes and Alarms Guide.
No. F30 is an open probe or wiring; F31 is a shorted one. Both use the same resistance chart.
Only at the end of the sheet's steps: wiring, then the probe, then the relay board.
Yes. It says to reset the unit by unplugging it for 30 seconds, or to flip the breaker if you cannot unplug. [6]
For F30, the model number, whether the oven heated at all, and whether F10 showed first.
Codes, symptoms, parts and service
F31 is a shorted oven temperature probe (RTD) or its wiring, on both Electrolux oven controls. Let the oven cool and restart the function. If F31 returns, book a technician; the sheets check the probe's resistance against a chart.
The written Electrolux articles say little about setting the clock or timer, since its display-settings guide is a video. What they do cover is a display or keypad that acts up: a stuck key (F11), memory and cable errors (F13, F14, F15), Demo mode and a power reset.
The RTD is the oven’s temperature probe: a resistance temperature detector that tells the control how hot the cavity is. F30 means the probe circuit reads open and F31 that it reads shorted. On ES630 controls, F10 can also first appear when the probe misreads.
Book a diagnostic for your model at the appliance.
Office details and the access information to pass on.