What it means
F31 is a shorted oven temperature probe (RTD) or its wiring, on both Electrolux oven controls. Let the oven cool and restart the function. If F31 returns, book a technician; the sheets check the probe's resistance against a chart.
Electrolux oven F31 / Temperature probe
F31 is a shorted oven temperature probe (RTD) or its wiring, on both Electrolux oven controls. Let the oven cool and restart the function. If F31 returns, book a technician; the sheets check the probe's resistance against a chart.
Also shown as F31
F31 is a shorted oven temperature probe (RTD) or its wiring, on both Electrolux oven controls. Let the oven cool and restart the function. If F31 returns, book a technician; the sheets check the probe's resistance against a chart.
The ES630 sheet's first step is to let the oven cool down and restart the function.
F31 returns after the oven cools.
Your checklist, kept on this device

The ES630 sheet's first step is to let the oven cool down and restart the function.

Switch it off at the breaker for 30 seconds and restore it.

F31 shows when the oven is active or you try to enter an active mode, so test with a simple bake.

The probe is part of the cavity wiring. Don't disconnect it.
ES630: replace the display board if it persists. Modular: check the probe circuit for a short, compare RTD resistance to the chart, replace the probe, then the relay board.
Send us the model and the checks you have done, and open your request here.
Book a visitA simplified drawing, since layouts differ between models. Pick an outlined part for its photo and the related check.

Component reference
The RTD is the oven’s temperature probe: a resistance temperature detector that tells the control how hot the cavity is.
Read the definitionThe temperature probe circuit reads as a short. The sheets word it shorted RTD sensor probe / wiring problem.
Read the supporting manualES630: let the oven cool, restart the function and, if it persists, replace the display board. Modular: it shares the F30 steps of wiring check, probe resistance and relay board.
Read the supporting manualF30 is an open circuit and F31 a shorted one. The cause is the probe or its wiring either way.
Read the supporting manualNo. The oven cannot read its own temperature.
Read the supporting manualManufacturer document
Electrolux (technician sheet; retailer-hosted copy)
Models: EW30EW65PS
p/n 807436903 (Rev A 13/04) / PDF p.1 (EOC code descriptions)
Manufacturer document
Electrolux (technician sheet; retailer-hosted copy)
Models: EW30EW55PS
p/n 807436904 (Rev A 13/04) / PDF p.1
Manufacturer document
Electrolux (technician sheet; retailer-hosted copy)
Models: EW30DS80RS
p/n 807880710 EN (Rev A 16/02); 807880711 FR (Rev A 16/03) / PDF p.1
Manufacturer document
Electrolux (technician sheet; retailer-hosted copy)
Models: EI30EW38TS
p/n A00980644 Rev A (2017/05) / PDF p.1
Manufacturer document
Electrolux (technician sheet; retailer-hosted copy)
Models: EI30EW48TS
p/n A00980645 Rev A (2017/05) / PDF p.2 (code table)
Row F31 of the ES630 sheets (807436903, 807436904, 807880710) and the modular sheets (A00980644, A00980645).
The ES630 sheet starts by letting the oven cool, so heat may play a part. It does not say how.
On the modular control the probe is replaced only if its resistance is off the chart.
F10 can appear from the same probe circuit, so a probe problem may show as F10 first.
For F31, the model number, when F31 appeared and whether the oven was hot.
Codes, symptoms, parts and service
F30 is an open oven temperature probe (RTD) or its wiring, on both Electrolux oven controls. Reset the power by unplugging for 30 seconds. The ES630 sheet adds that the control may show F10 first. If F30 returns, book a technician.
The written Electrolux articles say little about setting the clock or timer, since its display-settings guide is a video. What they do cover is a display or keypad that acts up: a stuck key (F11), memory and cable errors (F13, F14, F15), Demo mode and a power reset.
The RTD is the oven’s temperature probe: a resistance temperature detector that tells the control how hot the cavity is. F30 means the probe circuit reads open and F31 that it reads shorted. On ES630 controls, F10 can also first appear when the probe misreads.
Book a diagnostic for your model at the appliance.
Office details and the access information to pass on.