What it means
E92 is a user interface mother board protocol incongruence on Electrolux's 2018 washer sheet: the main board reports that the console speaks a different protocol. The display does not show E92. Book a technician for the interface test.
Electrolux washer E92 / Control board
E92 is a user interface mother board protocol incongruence on Electrolux's 2018 washer sheet: the main board reports that the console speaks a different protocol. The display does not show E92. Book a technician for the interface test.
Also shown as E92
E92 is a user interface mother board protocol incongruence on Electrolux's 2018 washer sheet: the main board reports that the console speaks a different protocol. The display does not show E92. Book a technician for the interface test.
Unplug the washer for a minute, plug it back in and see whether it reaches the normal start screen.
E92 is stored again or the buttons become unreliable.
Your checklist, kept on this device

Unplug the washer for a minute, plug it back in and see whether it reaches the normal start screen.

Press the keys one at a time. A panel that responds to some and not others tells a technician something.

A board or panel from another washer, even the same brand, can carry a different protocol. Mention any recent parts.

Power up, pause ten seconds, then hold the Temp and Select buttons together for a count of three.

Test 11 covers the wiring first and replacement of the interface board second.
Send us the model and the checks you have done, and open your request here.
Book a visit
A simplified drawing, since layouts differ between models. Pick an outlined part for its photo and the related check.

Component reference
The main control board runs an Electrolux front-load washer and talks to the user interface and the motor control.
Read the definitionFrom the main board's side, the console is not following the expected protocol. The sheet words it user interface mother board protocol incongruence error and does not show it to the owner.
Read the supporting manualIt checks the board-to-board wiring, corrects it if bad, otherwise replaces the interface board and finally the main board.
Read the supporting manualThey are the same kind of mismatch seen from opposite ends. E91 appears on the display; E92 stays in memory.
Read the supporting manualIf the panel works and cycles run, yes for now. A washer that ignores the buttons needs the visit sooner.
Read the supporting manualManufacturer document
Electrolux (technician sheet; retailer-hosted copy)
A11200302 (1803); 2018, 300/400/500/600 series (EFLS527UTT and EFLS627UTT copies are byte-identical) / p.2 (Washer Error Codes)
Row 92 of the 2018 washer sheet: stored only, test 11.
The sheet marks it as stored only. You would see odd panel behavior, or recall the code to find it.
The sheet checks wiring first, so the cheaper cause is ruled out before any board is replaced.
A reset can clear the message, but a mismatch that is real comes back.
The model number and any history of panel or board replacement.
Codes, symptoms, parts and service
E91 is a user interface protocol incongruence error on Electrolux's 2018 washer sheet: the console and the main board are not speaking the same protocol. The display shows it. Power-cycle once, then book a technician for the interface board test.
A washer that will not spin is most often reacting to an unbalanced or heavy load, a machine that is out of level, or a door that is not locked. Electrolux's sheet ties the motor-speed codes E55 and E59 to the motor, belt, tub bearings and motor control board.
The main control board runs an Electrolux front-load washer and talks to the user interface and the motor control. Electrolux's washer sheet names it for E91 to E94, E97 and E98, and for E84 where it says to replace the main board. The first step is one restart.
Book a diagnostic for your model at the appliance.
Office details and the access information to pass on.