What it means
E97 is a console or main board control problem, an incompatible cycle configuration, on Electrolux's 2018 washer sheet. The display shows it. Power-cycle once and book a technician for the interface board and wiring test.
Electrolux washer E97 / Control board
E97 is a console or main board control problem, an incompatible cycle configuration, on Electrolux's 2018 washer sheet. The display shows it. Power-cycle once and book a technician for the interface board and wiring test.
Also shown as E97
E97 is a console or main board control problem, an incompatible cycle configuration, on Electrolux's 2018 washer sheet. The display shows it. Power-cycle once and book a technician for the interface board and wiring test.
Unplug the washer for a minute and plug it back in.
E97 stays on the display after a restart.
Your checklist, kept on this device

Unplug the washer for a minute and plug it back in. If E97 returns at once, the cause is stored, not a passing glitch.

E97 is one of the codes the washer shows. Note the exact characters so the visit starts from the right row.

A new console or main board loaded with different cycle data is the plain reading of this code. Tell us about any recent part.

If the cycle you select is rejected, do not keep pressing Start. Leave the washer unplugged until it has been looked at.

Test 11 follows the wiring between the main and interface boards, then replaces the interface board, then the main board.
Send us the model and the checks you have done, and open your request here.
Book a visit
A simplified drawing, since layouts differ between models. Pick an outlined part for its photo and the related check.

Component reference
The main control board runs an Electrolux front-load washer and talks to the user interface and the motor control.
Read the definitionThe cycle table the console expects does not match the one on the main board. The sheet words it console or main board control problem (incompatible cycle configuration) and shows it on the display.
Read the supporting manualE94 blames the main board alone and goes to test 10. E97 blames the console or the main board and goes to test 11, the interface wiring.
Read the supporting manualTest 11: check the wiring between the main and the user interface boards. If it is bad, correct it; if good, replace the interface board and then, if needed, the main board.
Read the supporting manualNot if it rejects the cycle you pick. A washer that starts and finishes cycles normally can wait for a convenient visit.
Read the supporting manualManufacturer document
Electrolux (technician sheet; retailer-hosted copy)
A11200302 (1803); 2018, 300/400/500/600 series (EFLS527UTT and EFLS627UTT copies are byte-identical) / p.2 (Washer Error Codes)
Row 97 of the washer sheet: shown on the display. Test 11. It sits with E93 in the configuration group.
The sheet's display column says yes for E97. A mismatched cycle table affects what you can run, so the washer tells you.
Not necessarily. It means the panel and the main board do not agree. Wiring is checked before either board is replaced.
The sheet names no cause. A mismatch is more often a parts or wiring matter than a power event.
For E97, the model number, the exact display message and whether a panel or board has been fitted before.
Codes, symptoms, parts and service
E93 is a console or main board control problem on Electrolux's 2018 washer sheet: an incompatible machine configuration. The display shows it. Power-cycle once and book a technician; the sheet checks the wiring between the boards.
A washer that will not spin is most often reacting to an unbalanced or heavy load, a machine that is out of level, or a door that is not locked. Electrolux's sheet ties the motor-speed codes E55 and E59 to the motor, belt, tub bearings and motor control board.
The main control board runs an Electrolux front-load washer and talks to the user interface and the motor control. Electrolux's washer sheet names it for E91 to E94, E97 and E98, and for E84 where it says to replace the main board. The first step is one restart.
Book a diagnostic for your model at the appliance.
Office details and the access information to pass on.