Electrolux washer HF/BF / Control board

Electrolux washer
error HF/BF

Washer / display referenceHF/BF

HF or BF is a control relay sense failure on Electrolux's 2018 washer sheet: the control cannot confirm what its relay is doing. The display does not show HF/BF. Unplug the washer and book a technician for test 18.

Also shown as HF/BF

Last reviewed

Washer / display referenceHF/BF
Meaning
HF or BF is a control relay sense failure on Electrolux's 2018 washer sheet: the control cannot confirm what its relay is doing. The display does not show HF/BF. Unplug the washer and book a technician for test 18.
Who handles it
Technician
Related codes
Source
Washer Tech Data Sheet, A11200302 (1803)

What Electrolux washer HF/BF means.

What it means

HF or BF is a control relay sense failure on Electrolux's 2018 washer sheet: the control cannot confirm what its relay is doing. The display does not show HF/BF. Unplug the washer and book a technician for test 18.

What you can safely check

If the control cannot verify its relay, it cannot be sure that loads switch off.

When to call a technician

HF or BF is stored again.

Your checklist, kept on this device

Safe checks, in order.

0 of 5 checks done
  1. Electrolux washer HF/BF: Front-load washer with the top cover raised, showing a green control board with wiring beside the detergent drawer; the cord lies unplugged
    Illustration. Follow your model’s instructions.
    Before you begin

    Unplug the washer

    If the control cannot verify its relay, it cannot be sure that loads switch off. Keep the washer unplugged until it is checked.

  2. Washers in a thoughtfully designed home
    Illustration. Follow your model’s instructions.
    Check 2

    Note any stuck behavior

    A pump, valve or heater that runs when it should not is important to mention.

  3. A dark glass touch panel on a white front-load dryer, the display unlit
    Illustration. Follow your model’s instructions.
    Check 3

    Check the supply

    Make sure the plug is tight and there is no extension cord.

  4. Technician in navy coveralls holding a tablet with a blank checklist, a washer in the background.
    Illustration. Follow your model’s instructions.
    Check 4

    Recall the stored error

    Wait ten seconds after power-up and hold Temp and Select for three seconds.

  5. A technician inspecting a front-load washer pump filter
    Illustration. Follow your model’s instructions.
    Check 5

    Book a visit

    The sheet checks the supply, the wiring and then the main board.

Still showing HF/BF?

Send us the model and the checks you have done, and open your request here.

Book a visit

The control and its sensors.

Conceptual Washer sectionControl panelControl boardLevel sensorMotor wiring1234
  1. 1Control panel
  2. 4Motor wiring

A simplified drawing, since layouts differ between models. Pick an outlined part for its photo and the related check.

A little more context.

What does HF/BF mean?

The sense circuit that reports on a control relay is not giving a good reading. The sheet reads control relay sense failure and does not show it to the owner.

Read the supporting manual

Why does the sheet send it to test 18?

Test 18 covers the whole H and B family: power in, wiring to the main board, wiring to the motor board, then the main board.

Read the supporting manual

How is HF/BF different from HE/BE?

HE/BE is the relay. HF/BF is the control's sensing of it, so the relay may be fine while the reading is wrong.

Read the supporting manual

The manual behind the message.

Manufacturer document

Washer Tech Data Sheet, A11200302 (1803)

Electrolux (technician sheet; retailer-hosted copy)

A11200302 (1803); 2018, 300/400/500/600 series (EFLS527UTT and EFLS627UTT copies are byte-identical) / p.2 (Washer Error Codes)

Row HF/BF of the washer sheet: stored only; test 18.

Here to help

Good questions.
Clear answers.

Talk to our team
Is HF/BF a leak?

No. It is an electrical row about a relay sense circuit.

Does it show on the display?

No. The sheet marks HF/BF as not shown, so you recall it from the stored errors after a cycle stops.

Can I fix it myself?

No. The sheet's steps involve the supply and the board.

What helps the visit?

The model number and whether any load ran when it should not have.

Let’s take care of it.

Premium appliances deserve
careful service.